Topic: X-ecuter2.2 Pro Modchip Install - (Read 263 times)

snake3k1 · « **Reply #15 on:** July 26, 2003, 01:57:00 PM »

Wait it also flashes Red and Green on the power button.

snake3k1 · « **Reply #16 on:** July 26, 2003, 01:59:00 PM »

No number

snake3k1 · « **Reply #17 on:** July 26, 2003, 02:01:00 PM »

Give me a minute let me go see what happens.

vidgms4me · « **Reply #18 on:** July 26, 2003, 02:02:00 PM »

This is making no sense. Why are people getting the error screens? A correcly installed chip usually results in a Flashbbios screen, and an install that has no bios results in a frag, but I know for a fact that the x2.2's come prefkashed with the Flashbios.

snake3k1 · « **Reply #19 on:** July 26, 2003, 02:05:00 PM »

Okay, this is what's happening. All the bank switches are off and the chip is enabled. Everyone goes normal until the X comes up, there is nothing underneath it, usually MS is under it. While this is happening, the power button is green. When it Goes to the Languages screen, no error number is there and it tells me to contact MS for support in a few different languages. Plus it does the same thing with the chip is off.

johnyboy73 · « **Reply #20 on:** July 26, 2003, 02:06:00 PM »

The modchip is most probably not properly installed.. and there might be something wrong with your xbox if it doesn't boot normally when the modchip is disabled.

snake3k1 · « **Reply #21 on:** July 26, 2003, 02:09:00 PM »

Another thing, if the chip was properly installed without the BIOS, what should happen when i boot the box with the chip on? with the chip off? A pic off a web cam or a good descroption would be very appreciated

vidgms4me · « **Reply #22 on:** July 26, 2003, 02:11:00 PM »

QUOTE (snake3k1 @ Jul 26 2003, 06:09 PM)

Another thing, if the chip was properly installed without the BIOS, what should happen when i boot the box with the chip on? with the chip off? A pic off a web cam or a good descroption would be very appreciated

If that was the case, frag with it on, normal dash with it off.

And once again people, this is why everyone on this forum warns you *NOT* to use pogopins.

snake3k1 · « **Reply #23 on:** July 26, 2003, 02:12:00 PM »

SO its just supposed to flash red and green if it was working properly, nothing on the screen?

vidgms4me · « **Reply #24 on:** July 26, 2003, 02:14:00 PM »

QUOTE (snake3k1 @ Jul 26 2003, 06:12 PM)

SO its just supposed to flash red and green if it was working properly, nothing on the screen?

That would be the case if it had no bios. However the x2.2 comes preflashed with the flashbios.

snake3k1 · « **Reply #25 on:** July 26, 2003, 02:16:00 PM »

I'm using a X2,2 PRO which comes W/O preflashed BIOS

vidgms4me · « **Reply #26 on:** July 26, 2003, 02:18:00 PM »

QUOTE (snake3k1 @ Jul 26 2003, 06:16 PM)

I'm using a X2,2 PRO which comes W/O preflashed BIOS

*sigh* The x2.2 does come preflashed with the teamxecuter flashbios. I've said this many times in this thread.

snake3k1 · « **Reply #27 on:** July 26, 2003, 02:25:00 PM »

Okay well now It boots the MS dashboard when the chip is on and off, and remember, all the banks are set in the off position

vidgms4me · « **Reply #28 on:** July 26, 2003, 02:25:00 PM »

Its worth a try. It won't hurt anything if you do. The only thing it might take away is your ability to use the flashbios, but you can always use the parallel port then. There is always a chance your chip was not factory flashed as well.

snake3k1 · « **Reply #29 on:** July 26, 2003, 02:28:00 PM »

Please HELP!!

Author Topic: X-ecuter2.2 Pro Modchip Install - (Read 263 times)