Topic: The Newbie Guide To 007 - Auf Tsop Flashing (Read 1836 times)

hauss · « **Reply #345 on:** December 16, 2003, 10:31:00 AM »

Do I need to use XBTool here as the tutorial states or can I just use whatever X2 bios I download, assuming it's the right one for my xbox version?

I ask b/c there are other utils to make the bios 1MB..

Thanks

Zedek · « **Reply #346 on:** December 16, 2003, 10:40:00 AM »

you can use whatever works best for you

--Xtreme-- · « **Reply #347 on:** December 19, 2003, 11:22:00 AM »

Thanks man works great!!!

hauss · « **Reply #348 on:** December 19, 2003, 11:43:00 AM »

So if I use this method to flash my TSOP with say X2 4979 then I can play non original games on my xbox right... without doing anything to the xbox HD?

gunde · « **Reply #349 on:** December 25, 2003, 01:47:00 PM »

I'm going to buy a xbox tomorrow and it will probably be an v1.4 or 1.5? So my question is: Can i use this 007 hack guide to flash the bios? Does it work on the new versions of xbox? All i need to do is to sold little? Have someone tried this at a new xbox? Must be sure so i don't sold and it's not work.. I'm confused

lenselijer · « **Reply #350 on:** December 25, 2003, 01:59:00 PM »

I would certainly not try it!

I tried it myself and the points are very small and it's hard to get solder on. Also you can easily make a mistake and it will ruin your whole xbox.

Better just stay with the fonts exploits, they do the same...

A@ron · « **Reply #351 on:** December 25, 2003, 04:08:00 PM »

QUOTE (gunde @ Dec 25 2003, 05:40 PM)

I'm going to buy a xbox tomorrow and it will probably be an v1.4 or 1.5? So my question is: Can i use this 007 hack guide to flash the bios? Does it work on the new versions of xbox? All i need to do is to sold little? Have someone tried this at a new xbox? Must be sure so i don't sold and it's not work.. I'm confused

Yes it works on the newer thing but you need to solder 3 points (2 ontop and 1 on the bottom) and use raincoat .5 not the .3 release that is bundled on the usual places. All you need to do to make the .3 release .501 is download the raincoat .501 package from xbox-linux on sourceforge and then replace the raincoat and raincoat.conf files. Also you may need to add a few lines to the .conf file depending if your bios chip is listed in the file or not.

A@ron

gunde · « **Reply #352 on:** December 25, 2003, 11:56:00 PM »

Someone wrote this in another thread: With a 1.4 & 1.5 you only need to solder the top two links i.e two (2) solder bridges.

QUOTE

Yes it works on the newer thing but you need to solder 3 points (2 ontop and 1 on the bottom

Is it 2 or 3 links i have to solder? Should i use this 007 trick on a xbox version 1.4 or 1.5? If u r good at soldering this won't be a problem?

XBoxgeek · « **Reply #353 on:** December 26, 2003, 12:58:00 AM »

If you do not have a sharp TSOP then you only need to solder the 2 top points. If you have a sharp then you need to do 3.

Dreamcazman · « **Reply #354 on:** December 28, 2003, 12:06:00 PM »

QUOTE (lenselijer @ Dec 25 2003, 10:52 PM)

Better just stay with the fonts exploits, they do the same...

LOL, yeah right

Author Topic: The Newbie Guide To 007 - Auf Tsop Flashing (Read 1836 times)