Topic: Tsop Flash ALL Versions. (Read 1554 times)

phrozenfeonix · « **Reply #15 on:** February 06, 2004, 12:54:00 AM »

about the wire, what if i soldered the other points, then just put the wire on a switch, then mounted that... let's say on the back. would that work for a write-protection switch? and also, i have a TV capture card, if someone could give me a brief guide, i could go through and take all the pics, or movies, you need, just let me know!!

Ben999_ · « **Reply #16 on:** February 06, 2004, 06:06:00 AM »

cool guide

venturahighway · « **Reply #17 on:** February 06, 2004, 11:02:00 PM »

this sharp thread has a bit more to say about flashing sharp sharp tsops sharply.

blueinfinity · « **Reply #18 on:** February 07, 2004, 02:06:00 PM »

bucko · « **Reply #19 on:** February 08, 2004, 11:31:00 AM »

Erm, please include Version 1.4-5 info (Evox M7 to X4981.03) for focus support ortherwise peeps will start saying stuff bout it not botting up without a display.

blueinfinity · « **Reply #20 on:** February 09, 2004, 05:11:00 AM »

i just did a 1.4 with this m7 set up

you can upgrade the bios's yourself's theres a text file on there.
it's not difficult.

lookformeb · « **Reply #21 on:** February 09, 2004, 04:57:00 PM »

blueinfinity · « **Reply #22 on:** February 09, 2004, 11:16:00 PM »

yay

ya ive replied to all emails ive gotten as of late.

let me know how it goes
and for those who vote no.. WHY?
or are u jsut tryin to be jerks/?

wak4 · « **Reply #23 on:** February 10, 2004, 06:54:00 AM »

):

raincoat Flasher 0.5 [email protected] (tsop version by [email protected])
Checking for raincoat.cfg...
(Unable to open raincoat.cfg, using internal list)

UNKNOWN DEVICE Read Only??? manf=0x09, dev=0x00
Try adding the device ID to raincoat.cfg

I soldered both top and bottom pts and I have a 1.2. My chip is a ST M29F002B...

Thx

Wak4

blueinfinity · « **Reply #24 on:** February 10, 2004, 12:56:00 PM »

hmmm replace the bios file in
Mech-by-blue\4d530017\62D648EBF155\bios\
with a 256k bios instead of the 1mb...

then flash using evox

wak4 · « **Reply #25 on:** February 10, 2004, 01:24:00 PM »

Hi Blueinfinity

I didnt change the bios which was inside the pack... its already a 256 k

wak4

lookformeb · « **Reply #26 on:** February 10, 2004, 02:15:00 PM »

wak4

Try using Evox to flash. If it still tells you the same error, add these to your Evox.ini.

IF it stil says read only, your points aren't soldered correctly.

blueinfinity · « **Reply #27 on:** February 10, 2004, 02:48:00 PM »

no no your ev-x should be using a 1mb bios

and the eurasia should be using 256k.. put the 256 into where the 1mb is..

Corspegrinder99 · « **Reply #28 on:** February 10, 2004, 03:10:00 PM »

instead of doing all of that shit why not just get a chip?

wak4 · « **Reply #29 on:** February 10, 2004, 04:02:00 PM »

Hi

Um... Why should I use a 1mb bios if my xbox version is a 1.2 (which means a 256kb)... Sorry if this question is dumb, but I'd rather prefer not to make a door stop...

Thx

Wak4

Author Topic: Tsop Flash ALL Versions. (Read 1554 times)