Topic: 360 Modification Disc v1.52 (Read 1074 times)

FrostyTheSnowman · « **Reply #105 on:** April 10, 2009, 11:30:00 PM »

QUOTE(Jah Taz @ Apr 10 2009, 07:11 PM)

thank you Frosty for the new disc..... I used it successfully once but on the second sammy flash it fail at writing the 3rd bank this is the error i got :

updating 02% ww fail 70
0%6 status = fo should be 70

when i hooked it up back to the 360 i got error 65.....

good thing i had the key. I had to get a new board and use jungle flasher to flash my key to it thank God for spare parts...lol but its all good now just lost a drive.
I just need to know what went wrong?

I have seen that issue many times before... even before I made my disc.

That my friend is a dying flash chip on that samsung drive.

Its not the fault of you or my disc, just a bad chip.

slagboyz · « **Reply #106 on:** April 11, 2009, 05:01:00 AM »

When using this disc would it be wise to check a few times (booting back into Windows) that the firmware has backed up correctly and saved to c: drive before flashing or is it safe to continue without worrying?

Just about to install the Blaster360 before attempting this and thanks for the great disc.....
Don't fancy doing an XP install just to install Jungleflasher!

This post has been edited by slagboyz: Apr 11 2009, 12:02 PM

Jah Taz · « **Reply #107 on:** April 11, 2009, 04:16:00 PM »

QUOTE(FrostyTheSnowman @ Apr 10 2009, 10:06 PM)

I have seen that issue many times before... even before I made my disc.

That my friend is a dying flash chip on that samsung drive.

Its not the fault of you or my disc, just a bad chip.

kool i know it wasn't your disc because i use it and it worked before and i'm still using it...but i want to know what was the cause of the error, good to know what it finally is.....
keep up your good work and looking forward for the next update....nuff respect from Jamaica...bless!

kristonex · « **Reply #108 on:** April 11, 2009, 04:51:00 PM »

Great disc frosty! was shocked at how easy this was to upgrade my firmware! falcon box with benq drive upgraded from ixtreme1.41. If you can read and follow the instructions this method is simple. Thanks again to you and all involved in this wonderful piece of software

slagboyz · « **Reply #109 on:** April 12, 2009, 02:54:00 AM »

Hi, having a bit of an issue with attempting to use this disc... any pointers please?
I am using the CK3 to connect the drive to the pc to the internal VIA6421 port

1) Boot the disc up
2) Go through the initial setup (with the CK3 OFF)
3) When it asks to connect the cables to the drive (which already are) - PC FREEZES!!!!!!!

How do i get the drive on without locking the pc up?
I have tried to boot the pc up with the CK3 'ON' and the pc freezes on the VIA setup screen just after the bios....
Is there anything i am doing wrong?

Pc is running with Vista x64 - Don't fancy installing XP on a partition!!!

slagboyz · « **Reply #110 on:** April 12, 2009, 05:09:00 AM »

With regards to my comment above:
I have abandoned the whole Modification Disc idea and decided to get iPrep working.
Got iPrep working fine using the CK3 and took no more than 4 minutes to flash to iX1.51! (I hope!! - Just going to do test with a new backup!)

Many thanks for the help here....

Just need some more detailed guides to help 'noobs' like me, flash the 360 easier and without wasting everyone's time with basic questions..... which most of the times are answered by Google!!!

ALL GOOD!!! WORKED FIRST TIME!!!!! iXTREME 1.51 INSTALLED!!!!!

ITS LIKE CHRISTMAS CAME EARLY!!!!

This post has been edited by slagboyz: Apr 12 2009, 12:16 PM

FrostyTheSnowman · « **Reply #111 on:** April 12, 2009, 06:25:00 PM »

360 Modification Disc v1.53 is released, check the 'usual places'.

Changes in v1.53:

- Replaced MTKFlash for DOSFlash
- Improved Samsung Detection

This version fixes all detection issues with Samsung TS-H943 drives, and also improves compatibility with more SATA chipsets.

NOTE: I have also successfully used this disc with NForce3 chipsets, so even though I still recommend the VT6421 SATA card, you can also use the NForce3 too. (maybe others as well)

Enjoy!

dkellen1 · « **Reply #112 on:** April 13, 2009, 02:48:00 AM »

Okay, I just want to start out by saying that Frosty is officially the MAN!!! I was having issues with disc 1.52 not detecting any samsung drives, but with disc 1.53 I was upgraded to ixtreme 1.51 within a matter of minutes... (IMG:style_emoticons/default/biggrin.gif)

So easy a caveman can do it.... Ha Ha

I want to thank Frosty for all the time and effort that went in to making this disc... (IMG:style_emoticons/default/cool.gif)

FrostyTheSnowman · « **Reply #113 on:** April 13, 2009, 09:25:00 AM »

QUOTE(dkellen1 @ Apr 13 2009, 04:32 AM)

Okay, I just want to start out by saying that Frosty is officially the MAN!!! I was having issues with disc 1.52 not detecting any samsung drives, but with disc 1.53 I was upgraded to ixtreme 1.51 within a matter of minutes...

So easy a caveman can do it.... Ha Ha

I want to thank Frosty for all the time and effort that went in to making this disc...

Score dude!

Glad to hear you got it working.

alphabetically divided · « **Reply #114 on:** April 17, 2009, 03:34:00 AM »

QUOTE(FrostyTheSnowman @ Mar 20 2009, 02:24 AM)

Yes, my disc always requires a Lite-On serial adapter (CK3, homemade, etc) to mod or re-mod Lite-On drives.

Hello FrostyThesnowmam, do i need ck3,homemade etc stuff for the benq drive for mod with this disc?
thanks in advance

alphabetically divided · « **Reply #115 on:** April 19, 2009, 02:37:00 AM »

wulfie thanks bro

i willt try it and post back the results

alphabetically divided · « **Reply #116 on:** April 20, 2009, 04:19:00 AM »

didnt work for me ...i used dosflash to read and write and jungleflasher to make ixtreme..cheers

Author Topic: 360 Modification Disc v1.52 (Read 1074 times)