Topic: Help! Flashed 1mb Bios With 256k (Read 170 times)

Alpha1337 · « **on:** October 30, 2003, 07:46:00 AM »

Now it turns on *beep* turn off, turn on *beep* turn off, turn on *flash red*

Is there anyway I can reflash? I have an Xecuter Lite 2.2.

Alpha1337 · « **Reply #1 on:** October 30, 2003, 07:47:00 AM »

Xbox v1.2

anverc · « **Reply #2 on:** October 30, 2003, 07:50:00 AM »

QUOTE (Alpha1337 @ Oct 30 2003, 04:36 PM)

Xbox v1.2

1.2 requires a 256k bios

you probably put a bad bios on there (or wrong version)... or the flash didn't complete itself.

You need to put on a 29 wire mod to fix it, or put on an LPC mod and leave it on there.

Alpha1337 · « **Reply #3 on:** October 30, 2003, 08:07:00 AM »

sorry it is 1.1 then im sure it has a 1MB bios has the oldschool dvdrom. would i use same method? i only have an xecuter lite 2.2

venturahighway · « **Reply #4 on:** October 30, 2003, 08:22:00 AM »

if you flashed with the LPC mod trick just try it again.

you can also just tie the A19 and A18 address lines to ground. this forces it to read first bank 4 times.

dvd rom means nothing, what brand TSOP do you have?

This post has been edited by venturahighway: Oct 30 2003, 04:23 PM

Alpha1337 · « **Reply #5 on:** October 30, 2003, 08:33:00 AM »

what is LPC mod? i used 007exploit is this the same?

here is a pic of my tsop's (i think) they all say samsung:
(IMG:http://www.kindlespine.com/bios.jpg)

venturahighway · « **Reply #6 on:** October 30, 2003, 08:41:00 AM »

that would be your memory.
you have v1.0 (1Meg)

the tsop is near the top write enable point you must have soldered.

solder ground to A19 and A18 in the first pic in this tut.

ground is that red circle on that yellow block.

no switch, just wires. then see if it will boot.

This post has been edited by venturahighway: Oct 30 2003, 04:42 PM

Alpha1337 · « **Reply #7 on:** October 30, 2003, 08:50:00 AM »

so i should run a wire from both of those points to the ground?

venturahighway · « **Reply #8 on:** October 30, 2003, 08:51:00 AM »

Alpha1337 · « **Reply #9 on:** October 30, 2003, 08:52:00 AM »

i have a friends box with a similar problem it was flashed with 007 and he bought a xecuter and flashed with cromwell now its having the same problem, can i use this same method?

venturahighway · « **Reply #10 on:** October 30, 2003, 08:55:00 AM »

this is only for when you flashed a 1M tsop with a 256K bios.

let us know how it goes.

This post has been edited by venturahighway: Oct 30 2003, 05:16 PM

Alpha1337 · « **Reply #11 on:** October 30, 2003, 09:16:00 AM »

amazing help! thank you so much.

venturahighway · « **Reply #12 on:** October 30, 2003, 09:16:00 AM »

so it worked?

Alpha1337 · « **Reply #13 on:** October 30, 2003, 09:23:00 AM »

yes it worked? now would i flash again with 007 just this time use the right bios =

venturahighway · « **Reply #14 on:** October 30, 2003, 09:26:00 AM »

no, you have to boot with A19 and A18 grounded, then cut them while it is on (you may have to run long wires out of the box).

then flash with a 1M.

Author Topic: Help! Flashed 1mb Bios With 256k (Read 170 times)