Topic: 1.0 Solder Filled (Read 232 times)

The LukeMan · « **on:** January 07, 2004, 09:48:00 PM »

Yep ther filled the lpc points but ive been reading the x ecuter 2.3b lite + should still work without desoldering the points is this true ??

sorry thought i was in hardware forum <_<

This post has been edited by The LukeMan: Jan 8 2004, 05:49 AM

bleugh · « **Reply #1 on:** January 08, 2004, 01:33:00 AM »

?

if you have a pin, it still needs to go in a hole,

if you dont have a hole then two choices,

1) make a hole (desolder)
2) solder wires into the hole

either way some soldering or desoldering is needed!

DynaMight · « **Reply #2 on:** January 08, 2004, 03:14:00 AM »

Just use the wire install, No need to remove any solder. It's prolly easier than the header pin too. You could probably do the whole thing without using any solder.

deviation56 · « **Reply #3 on:** January 08, 2004, 03:16:00 AM »

i have a 2.3 lite + and a 1.0 xbox with the holes filled and i never had to desolder anything...

The LukeMan · « **Reply #4 on:** January 08, 2004, 03:16:00 AM »

well im going to try dangling the pins over the lpc ports and that way it should make a contact althought it could possibly not be 100% stable

moistness · « **Reply #5 on:** January 08, 2004, 03:21:00 AM »

QUOTE (The LukeMan @ Jan 8 2004, 02:10 PM)

well im going to try dangling the pins over the lpc ports and that way it should make a contact althought it could possibly not be 100% stable

If you are talking about a pogo install, then it should "work" as well as any pogo install!

Nothin beats a good header pin install though!

The LukeMan · « **Reply #6 on:** January 08, 2004, 03:24:00 AM »

Yep its an xecuter 2.3 lite + chip non solder
so i plan to place the pins carefully over the lpc points that are filled then screw it in it better work :lol:

moistness · « **Reply #7 on:** January 08, 2004, 03:27:00 AM »

just realised that you have posted this twice, both times in the wrong forums!

one in general h/w, one in case + h/w modding, should be in newbie chat!

*slap*

The LukeMan · « **Reply #8 on:** January 08, 2004, 03:35:00 AM »

s0orry about that

FunkmaztafoX · « **Reply #9 on:** January 08, 2004, 06:55:00 AM »

i have a v1.0 and didn't have to solder or desolder anything and my lpc's are filled

The LukeMan · « **Reply #10 on:** January 09, 2004, 07:27:00 AM »

Hello yeh can the xecuter 2.3b lite + non solder chip be fitted on to these filled ports in my xbox see below

(IMG:http://www.angelfire.com/creep/lukeman/lpcports.jpg)

Flagg3 · « **Reply #11 on:** January 09, 2004, 02:04:00 PM »

Umm, someone correct me if I'm wrong, but weren't all of the X2+ modchips designed to be used WITH the lpc holes filled?

AFAIK, all pogo pin modchips work best with filled solder holes.

Can't say for sure, as I haven't used Pogos since the Matrix.

Flagg

This post has been edited by Flagg3: Jan 9 2004, 10:04 PM

Author Topic: 1.0 Solder Filled (Read 232 times)