Topic: X3 Install Problem..(v1.6) (Read 182 times)

00g · « **on:** March 17, 2005, 12:30:00 PM »

I just installed the X3ce chip into my 1.6.

When I push the power button, the system boots up as normal.

The little blue LED on the chip lights up. But nothing happens on the little panel you put on the outside of the XBOX.

What could I have done wrong?

00g · « **Reply #1 on:** March 17, 2005, 12:43:00 PM »

Do I have to move any of these pin switches on the external switch?

EDIT: I just tried booting with each of the 5 switches set to "on" (individualy). Nothing.

Also the "hold down the power button" feature works. When I hold it down, the LED on the underside of the chip lights up, then after a second, the box boots up....the only problem is it boots up normally both ways.

G_Prime99 · « **Reply #2 on:** March 17, 2005, 01:42:00 PM »

do both blue lights on the chip light up or just one?

00g · « **Reply #3 on:** March 17, 2005, 01:48:00 PM »

QUOTE(G_Prime99 @ Mar 17 2005, 02:48 PM)

do both blue lights on the chip light up or just one?

00g · « **Reply #4 on:** March 17, 2005, 01:50:00 PM »

Ok. It looks like there's an light on each side of external switch connector. The only one that's coming on is the one closest to the front of the XBOX.

G_Prime99 · « **Reply #5 on:** March 17, 2005, 01:54:00 PM »

Thats teh 5v connection, your not geting a 3.3v connection, cheak your solder points at pin 9 and 15

Hexx · « **Reply #6 on:** March 17, 2005, 02:03:00 PM »

What, may I ask, is that avatar 00g?
*Edit* I see what it clearly is now, I had mt resolution up to much, it hard for me too see. I got it now though.

G_Prime99 · « **Reply #7 on:** March 17, 2005, 02:08:00 PM »

QUOTE(Hexx @ Mar 17 2005, 03:09 PM)

What, may I ask, is that avatar 00g?

accukevin · « **Reply #8 on:** March 17, 2005, 02:09:00 PM »

Clearly it is a 10 gauge (mabye) barbell, moving up and down through someone's tounge. They also appear to have a pierced lip.

G_Prime99 · « **Reply #9 on:** March 17, 2005, 02:12:00 PM »

I found this pic on the Team Xecuter Forum....

00g · « **Reply #10 on:** March 17, 2005, 02:24:00 PM »

QUOTE(G_Prime99 @ Mar 17 2005, 03:00 PM)

Thats teh 5v connection, your not geting a 3.3v connection, cheak your solder points at pin 9 and 15

G_Prime99 · « **Reply #11 on:** March 17, 2005, 02:42:00 PM »

have u flashed the chip yet with the correct switches toggled? dont forget you just tap the power putton dont hold it.

00g · « **Reply #12 on:** March 17, 2005, 02:52:00 PM »

QUOTE(G_Prime99 @ Mar 17 2005, 03:48 PM)

have u flashed the chip yet with the correct switches toggled? dont forget you just tap the power putton dont hold it.

G_Prime99 · « **Reply #13 on:** March 17, 2005, 02:55:00 PM »

have u flashed the BIOS yet? if not you need to hit eject+power at the same time to bring up "FlashBIOS v3.0.0"

There is a great tut' at TeamXecuter- here is the link - http://www.teamxecuter.com/flashbios/

00g · « **Reply #14 on:** March 17, 2005, 02:59:00 PM »

I have done nothing but take it out of the bubble wrap, and solder it in as described in the tut.

Eject + Power button at the same time does absolutely nothing.

Author Topic: X3 Install Problem..(v1.6) (Read 182 times)