xboxscene.org forums

Author Topic: Are My Lpc Holes Soldered Shut?  (Read 50 times)

Y2Kevbug11

  • Archived User
  • Newbie
  • *
  • Posts: 4
Are My Lpc Holes Soldered Shut?
« on: September 07, 2004, 03:51:00 PM »
Oh, I did more reading and I noticed that they have solder. I should just remove solder in ALL the holes?
Logged

imamafackinhokie

  • Archived User
  • Sr. Member
  • *
  • Posts: 327
Are My Lpc Holes Soldered Shut?
« Reply #1 on: September 07, 2004, 03:52:00 PM »
The points are soldered and you have a version one, but if you are using a solderless adaptor you do not need to desolder the points.
Logged

Y2Kevbug11

  • Archived User
  • Newbie
  • *
  • Posts: 4
Are My Lpc Holes Soldered Shut?
« Reply #2 on: September 07, 2004, 03:53:00 PM »
QUOTE (imamafackinhokie @ Sep 7 2004, 11:55 PM)
The points are soldered and you have a version one, but if you are using a solderless adaptor you do not need to desolder the points.

I am using the solderless adapter. I don't have to do anything? I don't need to put the rivets in or anything? I just leave it there?

Okie dokie then. I shall try that.
Logged

frostedflakes

  • Archived User
  • Newbie
  • *
  • Posts: 16
Are My Lpc Holes Soldered Shut?
« Reply #3 on: September 07, 2004, 04:23:00 PM »
laugh.gif
Logged

acemilo

  • Archived User
  • Hero Member
  • *
  • Posts: 910
Are My Lpc Holes Soldered Shut?
« Reply #4 on: September 07, 2004, 04:45:00 PM »
IMO if you are gonna take the time to remove the solder from the holes, you may as well install the pinheader and solder the chip in so you won't have problems with it later on.
Logged

frostedflakes

  • Archived User
  • Newbie
  • *
  • Posts: 16
Are My Lpc Holes Soldered Shut?
« Reply #5 on: September 07, 2004, 04:50:00 PM »
wink.gif

I actually just received my modchip in the mail. Already have the pin header soldered to the board, so all I need to do is burn my dashboard to a disc and get everything set up. Should be a fun night.

Anyways, good luck with your mod Kev.

P.S. Just curious, but where are the FXB guys hanging out now?
Logged

Y2Kevbug11

  • Archived User
  • Newbie
  • *
  • Posts: 4
Are My Lpc Holes Soldered Shut?
« Reply #6 on: September 07, 2004, 05:03:00 PM »
QUOTE (frostedflakes @ Sep 8 2004, 12:53 AM)
Took ya long enough! wink.gif

I actually just received my modchip in the mail. Already have the pin header soldered to the board, so all I need to do is burn my dashboard to a disc and get everything set up. Should be a fun night.

Anyways, good luck with your mod Kev.

P.S. Just curious, but where are the FXB guys hanging out now?

www.geekpub.com

Frank set it up as a place for us to whine and yell at each other. Somehow we get along.
Logged

Y2Kevbug11

  • Archived User
  • Newbie
  • *
  • Posts: 4
Are My Lpc Holes Soldered Shut?
« Reply #7 on: September 07, 2004, 06:26:00 PM »
I had a weak connection, so I am trying to desolder the LPC ports with braid...how does it work?

I hold the soldering iron above the braid and press down, but it is only sucking a little at a time. Can someone give me advice? I can't get it all out of the hole.
Logged

acemilo

  • Archived User
  • Hero Member
  • *
  • Posts: 910
Are My Lpc Holes Soldered Shut?
« Reply #8 on: September 07, 2004, 09:53:00 PM »
Put a little flux on the lpc, then put a little bit of solder on the iron (just a little) and put the braid over the hole and hold the iron so that the braid is touching the solder to be removed then touch the iron to the braid and the solder will flow up the braid.  Once it stops flowing, remove the iron, cut off the used part and repeat until its gone.
Logged

counter terrorist dan

  • Archived User
  • Full Member
  • *
  • Posts: 178
Are My Lpc Holes Soldered Shut?
« Reply #9 on: September 08, 2004, 06:54:00 AM »
use a desoldering bulb. Buy them at radio shack and such, it's next to impossible with desoldering braid.
Logged