Print

[Ph34rMe]

Whether you got it to work or not please let me know the following.

1.  Xbox version
2.  Where did you buy your Xbit
3.  What OS are you using to flash your Xbit
4.  What  configuration are you using
5.  Did you get it to work
6.  Problem

Mine:

1.  Xbox v1.1
2.  I got mine at The Console Corner
3.  I used XP at first, but that didn't work.  So I ended up using 98.
4.  I'm using the first two banks of configuration 6
5.  YES
6.  Nothing

This is my attempt to find similarities for those of us who had problems and those who didn't.

This post has been edited by Ph34rMe: Oct 22 2003, 02:04 AM

[Arakon]

1) 1.2 LE
2) nowhere
3) win2k, USB2.0 addon card cause of the nforce2 problem
4) config 5(?), 6 bioses, usually switched to bank 3 with x2 4977
5) yup
6) none

[gadgetaddict]

1.0 refurbed xbox, xbit mode 6, using bank 3 with M7, pogo installs, soldered diode and wire to xbit, slapped wire into xbox harness, all working perfectly, no problems

[gamer4ever]

1. Xbox version - 1.0
2. Where did you buy your Xbit - Buy, See, and Trade fourm(used)
3. What OS are you using to flash your Xbit - win 98se and win 2000 pro
4. What configuration are you using - I've used them all
5. Did you get it to work - Yup
6. Problem - None

[chelrob]

1. Xbox version - v1.1 (just bought it "new")
2. Where did you buy your Xbit - Console Corner
3. What OS are you using to flash your Xbit - XP Pro
4. What configuration are you using - #6.  2X512 & 4X256.  Falshed bank 3 with M7-EF
5. Did you get it to work - Yes, after reseating chip once.  POGO install.
6. Problem - None.  Works fine.  Boots to EVOX when enabled and original MS dash when disabled.

Maybe you have a defective chip?

[[[CWB]]-Master-]

1. Xbox version 1.0
2. Where did you buy your Xbit? Divine UK
3. What OS are you using to flash your Xbit? Windows XP
4. What configuration are you using? Flashed it with the 6th Format, Placed m7 Bios on Bank 6
5. Did you get it to work? Yes
6. Problems? NONE! Works like a charm

[...ranma]

1. Either 1.2 or 1.3, not sure which.
2. Divineo UK
3. Win XP Home SP1
4. Config 6
5. Yes
6. Had problems with an adaptec USB2 PCI card and formating the flash.  Switched to built in USB1 on my KT7A-RAID MB and it worked fine.  Also had to scrape point D0 a bit.
7. Installed via pogo pins.

It's currently working with no problems :luv: , and I Just had ...Rellik install the wire to the power button for disabling the mod chip without using the STM switch.  

[DeadBaby]

I've installed it on two xboxes:

Xbox1:
1) 1.4
2) Console Corner (very fast shipping)
3) Windows 2000
4) Wire install
5) Yes, but I almost killed my board trying to install it.
6) I did a sloppy job on the D0 point and damaged a trace, luckily it was fixable.

Xbox2:
1) 1.0
2) Console Corner
3) Windows 2000
4) Pogo pin install
5) Yes
6) No problems, worked perfectly on the first try.

[flownez]

1. V1.0
2. Divino
3. Win2K
4. Header Pin Install
5. Bank Config 6
6. Removing the "1 wire method" chepmod installation.... eek.

[chefelf]

1. Xbox version 1.0
2. Where did you buy your Xbit http://www.the-console-corner.com
3. What OS are you using to flash your Xbit WinXP
4. What configuration are you using Pogopin.
5. Did you get it to work Yes.
6. Problem Only with getting the flashing software to work.  I had to try four different computers before it worked but once it worked it worked beautifully.

[Workshed]

1. Xbox version? 1.3
2. Where did you buy your Xbit? www.simplymods.net
3. What OS are you using to flash your Xbit? Windows XP
4. What configuration are you using? M7 BIOS in bank 6
5. Did you get it to work? Yup!
6. Problem? scraping D0, isnt it funny how they dont mention that on the instructions on the XBIT website!

[Spice Guy]

1. Version 1.0
2. Divineo UK
3. Windows XP Professional
4. Bank 6 - Xecuter 2 v4978.03 Bios, 2 x EvoX D6 Bios, & 3 x EvoX M7 Bios
5. Yes!
6. No Scraping of D0, only problem is wont boot in STM.