Topic: R-jtag Booting To Xellreloaded But Dont Know Hot To Install Fsd (Read 236 times)

wilgo45 · « **on:** May 23, 2013, 05:00:00 PM »

FSD boots from the Hard Drive.

You have to install FSD into the Hard drive. Jtag and Rgh just allow its routine to boot.

Do you have normal boot up to a Dashboard ?

dopesun · « **Reply #1 on:** May 23, 2013, 06:05:00 PM »

if you have internet connection the best and most fool proof way to get the latest FSD which is REV 735 is to download the ISO.. burn it with IMGBURN.. and launch it through NXE..

have your HDDs attached and it will install it to your preferred location..

tutorial http://www.youtube.c...p;v=bxtscmOy5Mw

Edited due to technical difficulties..

dopesun · « **Reply #2 on:** May 23, 2013, 06:20:00 PM »

BTW.. where did you get your kit from? mine stock just shipped today.

nikki81 · « **Reply #3 on:** May 23, 2013, 07:18:00 PM »

Yes It boots up to the normal Xbox dash when I press the power button and not the DVD eject.

I got my kit from ck3

steveo1978 · « **Reply #4 on:** May 23, 2013, 07:19:00 PM »

Basic J-Runner Instructions

There are for more indepth guides to using J-Runner however is as a simple breakdown of the steps required for the new R-JTAG option:

Note: Minimum dashboard version required is 15574.

1. Read NAND (compare)
2. Tick JTAG radio button
3. Select AUD_CLAMP On or OFF depending on JTAG QSB installation
4. Create xell reloaded
5. Write xell reloaded
6. Boot to xell, get cpu key
7. Create image of newest dash version
8. Write nand
9. Use rater to fine tune boot times

Found Here

did you do all of that?

dopesun · « **Reply #5 on:** May 23, 2013, 08:03:00 PM »

QUOTE(nikki81 @ May 23 2013, 09:18 PM)

Yes It boots up to the normal Xbox dash when I press the power button and not the DVD eject.

I got my kit from ck3

When you press the power button you should get the NXE dashboard.. When you press the eject button your supposed to get Xell Reloaded..

Please follow my instructions if you want Freestyle Dash..

I never heard of a retailer called CK3...

QUOTE(steveo1978 @ May 23 2013, 09:19 PM)

Basic J-Runner Instructions

There are for more indepth guides to using J-Runner however is as a simple breakdown of the steps required for the new R-JTAG option:

Note: Minimum dashboard version required is 15574.

1. Read NAND (compare)
2. Tick JTAG radio button
3. Select AUD_CLAMP On or OFF depending on JTAG QSB installation
4. Create xell reloaded
5. Write xell reloaded
6. Boot to xell, get cpu key
7. Create image of newest dash version
8. Write nand
9. Use rater to fine tune boot times
Found Here

did you do all of that?

I could have sworn he said he wants to install Freestyle Dash...

steveo1978 · « **Reply #6 on:** May 23, 2013, 08:44:00 PM »

QUOTE(dopesun @ May 23 2013, 09:03 PM)

I could have sworn he said he wants to install Freestyle Dash...

Yeah but the he only said it boots Xell left me thinking he he did not finish the mod. Also Linking to software built using the XDK is against forum rules.

dopesun · « **Reply #7 on:** May 23, 2013, 09:18:00 PM »

NP.. Usually RDC is the one coming down on me when i make a mistake and break the rules..

My bad..

but.. he should get the picture..

nikki81 · « **Reply #8 on:** May 23, 2013, 09:33:00 PM »

Thanks for your help ! All done and booting into fsd

here is the link to the shop were I got my kit http://www.ck3.co.uk

Thanks

Author Topic: R-jtag Booting To Xellreloaded But Dont Know Hot To Install Fsd (Read 236 times)