Topic: XeLL Updater v1.2 (Read 311 times)

Xbox-Scene · « **on:** July 21, 2011, 11:36:00 PM »

XeLL Updater v1.2
Posted by XanTium | July 22 01:36 EST | News Category: Xbox360

Tuxuser released a new version of his homebrew application that will allow you to easily update just the XeLL part of your freeBOOT NAND. It'd been updated following fbBuild v0.32's release, and adds support for the 13599 kernel:

Quote

XeLL Updater for freeBOOT - v1.2
for Kernel 9199, 12611, 12625, 13146 and 13599
Based on dashlaunch installer by cOz

This little tool is needed to update XeLL in Flash/NAND properly. The freeBOOT/fbBuild Rebooter has a different layout compared to XBR or pure-XeLL images so the XeLL binary isn't at the beginning of a NAND Block anymore.

Using the old updslot0/updslot1-Method (which worked on XBR and XeLL Images just fine) you would render your freeBOOT console non-booting (until you reflash it externally of course).

This application however works for freeBOOT/fbBuild It reads the specific part of the NAND, injects the XeLL binary and writes the blocks back.

Use it on Single-NAND freeBOOT only (9199, 12611, 12625, 13146 and 13599).

Official Site: http://libxenon.org
Download: n/a (built with XDK)
News-Source: xbins.org

danthaman673 · « **Reply #1 on:** July 22, 2011, 11:23:00 AM »

Does anyone know of any advantage to updating Xell (other than for Linux360 users?) Is it needed for running new dashlaunch? If so will it be included in the DL installer payload? Or is it like a one-time update, basically just replacing the old update system which addresses the wrong segment (I'm guessing the latter, but it never hurts to ask ;-)

Cheers For any help, If I wasn't lacking sleep so bad I would probably be able to figure it out myself

Damm technology based sleep-deprivation !

Thanx fer the dev-up!

Twis7eD · « **Reply #2 on:** July 22, 2011, 04:29:00 PM »

QUOTE(danthaman673 @ Jul 22 2011, 12:23 PM)

Does anyone know of any advantage to updating Xell (other than for Linux360 users?)

One of the updates included HDMI support, which wasn't initially part of XeLL/Xellous. That's probably the most dramatic change. Everything else is probably small updates to different parts of the code.

cancerous1 · « **Reply #3 on:** July 23, 2011, 12:00:00 AM »

thanks again Tuxuser XD. you can look on libxenon.org to see what changes have been/ are being worked on.

This post has been edited by cancerous1: Jul 23 2011, 07:17 AM

uN0pEn · « **Reply #4 on:** July 27, 2011, 09:17:00 AM »

Thanks!

moeom · « **Reply #5 on:** July 28, 2011, 12:09:00 PM »

I'm interested in the HDMI support, but i have Xellous (not Xell). I'm guessing i cannot use this updater. Am i correct?

moeom · « **Reply #6 on:** August 01, 2011, 02:10:00 PM »

QUOTE(moeom @ Jul 28 2011, 02:09 PM)

I'm interested in the HDMI support, but i have Xellous (not Xell). I'm guessing i cannot use this updater. Am i correct?

No one?

Twis7eD · « **Reply #7 on:** August 11, 2011, 11:45:00 PM »

QUOTE(moeom @ Aug 1 2011, 03:10 PM)

No one?

I assume that you can still use it. I would assume that if they wanted to make an updater, they would accommodate for all versions of XeLL/Xellous. I have no actual proof of this, though.

Dra60nSlayer · « **Reply #8 on:** August 29, 2011, 01:42:00 PM »

QUOTE(Xbox-Scene @ Jul 22 2011, 07:36 AM)

Use it on Single-NAND freeBOOT only (9199, 12611, 12625, 13146 and 13599).

What do i use? for update to Xell Reloaded on my Cygnos V2 rev B

razkar · « **Reply #9 on:** November 28, 2011, 04:12:00 PM »

Author Topic: XeLL Updater v1.2 (Read 311 times)