Print

[rastiemon]

I just updated one for a friend a few minutes ago and did the usb update but then it prompted again for a update after the kinect was plugged in.    Accepted that and it worked fine.  

So first check if your avatars are showing up

Second plug in the kinect and see if it prompts you for a update.



Also I am sure this is common sense but make sure you are using 14699 update if you are on 14699 etc.

[mac-life]

QUOTE(steplay29 @ Dec 11 2011, 07:31 PM)

hi guys was just wondering does the nand dump have to be an original one or could you use a dump of your current one (13604).i used a dump of my last one to upgrade to (13604)think prog was ggbuild.i have a jasper 512mb jtag.i put my nand dump and cpu key in different folders (forget names)and ran a command line for my jasper to create new image.

Does not have to be the original dump. Just use flash360 tool to make an nanddump file of your current dash and create the 14699 image using that. Then flash the 14699 dash with flash360 keeping current settings. Worked perfectly on an xenon. Also nanddump.bin and cpukey.txt goes in my360 directory.

[wlintek]

just wondering what's the right and best way to update from RGH 13604 to 14699. it seems that using 13604 original or hacked images to create RGH 14699 image will not work.

i have two RGH Xbox to update. the first one i restored to stock 13604, then updated to stock 14699 via USB stick, then re-dumped the nand and created the 14699 RGH image with the dump. it finally worked for me.

but the second one, i tried both 13604 hacked and original to create the 14699 image, although the creation went fine, the Xbox just does not boot with the image i created.

[steplay29]

hi just updated a jasper 512mb with the new version 0.7 and it worked a treat even for me lol.am going to to the kids two falcons v3 but when i run the progam beside option 5:it says a falcon with cb 5771,but my two falcons are 5770.just wondering is it ok to go ahead and flash this or to wait?


p.s sorry for the double post guys.posted this in thread about version 0.3 aswell.

[danthaman673]

Thanx again Rogero, Ver 7 rox!

[Midnight Tboy]

guessing it will be better to use a backup of my current nand, rather than basing it on the default nand?

That way would keep all settings like kinect configuration, blocked live settings etc

[steveo1978]

QUOTE(drysset @ Dec 13 2011, 07:06 AM)

Newer used multi builder before.

Should I install FSD before I update my JTAG with dashlaunch preinstalled in the nand image?
And I just flash my JTAG with flash360?

Use multi builder v0.7 its easy to do it either way.

@Midnight TboyI am not sure where those setting are actually saved but they maybe not effected by flashing the NAND.

Just if either of you have a 256MB or 512MB Make sure you backup everything.

[HiGhLaNdR]

QUOTE(steplay29 @ Dec 12 2011, 01:18 PM)

hi just updated a jasper 512mb with the new version 0.7 and it worked a treat even for me lol.am going to to the kids two falcons v3 but when i run the progam beside option 5:it says a falcon with cb 5771,but my two falcons are 5770.just wondering is it ok to go ahead and flash this or to wait?
p.s sorry for the double post guys.posted this in thread about version 0.3 aswell.

Had the same problem, it even changed the smc version to 2.3 instead of 1.6. The xebuild Gui v1.1 did the job, kept the 1.6 and the cb 5770.

My 5 cents.