Topic: Phoenix Bios Loader V1.3 (Read 1854 times)

gBOX · « **Reply #30 on:** July 31, 2003, 09:08:00 AM »

Dude, you're getting a new BIOS!

caio1 · « **Reply #31 on:** July 31, 2003, 09:12:00 AM »

But with a BFM may I boot from c:evoxdash.xbe or just from the dvd-rom unit?

Thank you,
Caio

bull · « **Reply #32 on:** July 31, 2003, 09:27:00 AM »

ok guys kinda a n00b question (I can't remember anything from uni) when you say the eeprom data from 0x1c do you mean offset 000001C0 ? which would be something like xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx in hex, and is it this hex value I paste in or do I put the ascii value?

TIA.

[-bull-]

LafferUSA · « **Reply #33 on:** July 31, 2003, 09:35:00 AM »

QUOTE (caio1 @ Jul 31 2003, 06:12 PM)

But with a BFM may I boot from c:evoxdash.xbe or just from the dvd-rom unit?

Thank you,
Caio

You can boot from c:\evoxdash.xbe

Thank you,
Laffer

[)eacon]ndigo · « **Reply #34 on:** July 31, 2003, 09:46:00 AM »

Change your file size setting to 1024k.

4NIC8TOR · « **Reply #35 on:** July 31, 2003, 09:50:00 AM »

Tried that...none of the 3 file sizes work...I still get the same error

....hmmm, just looked at the filesize and for some reason it's only 137KB.......this is from the Xecuter2.Build.4977.rar on xbins!?

4NIC8TOR · « **Reply #36 on:** July 31, 2003, 09:59:00 AM »

....ok, it didn't need an rc4 key in the config file....now to find it in hex workshop....

4NIC8TOR · « **Reply #37 on:** July 31, 2003, 10:09:00 AM »

QUOTE (bull @ Jul 31 2003, 06:27 PM)

ok guys kinda a n00b question (I can't remember anything from uni) when you say the eeprom data from 0x1c do you mean offset 000001C0 ? which would be something like xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx in hex, and is it this hex value I paste in or do I put the ascii value?

TIA.

[-bull-]

I have the same question....because there is no 0x1c in hex workshop.....just addresses like 0x0000001C???

mohawk23 · « **Reply #38 on:** July 31, 2003, 10:12:00 AM »

for those looking for eeprom keys look in recent threads for topic eeprom keys excellent step by step there

4NIC8TOR · « **Reply #39 on:** July 31, 2003, 10:26:00 AM »

ok....that worked.....I still wish I could've figured out how to do it in Hex Workshop so I didn't have to dload a new editor (XVI32)....but thank you very much!!!

warbeast · « **Reply #40 on:** July 31, 2003, 10:36:00 AM »

to use a bfm bios with xbtool u need to put a debug.ini with the rc4key inside next to the multi.ini the open xbtool change it to debug where it says multi then u can open your bfm bios and change it to whatever

{later} · « **Reply #41 on:** July 31, 2003, 10:52:00 AM »

that's ok, use it!

Anusko · « **Reply #42 on:** July 31, 2003, 11:11:00 AM »

I've extracted the eeprom key myself but it's not similar with the one that warbeast posted.
There are different eeprom keys?

warbeast · « **Reply #43 on:** July 31, 2003, 11:14:00 AM »

sorry i did put loads of 0s into it before i posted!

monkeh · « **Reply #44 on:** July 31, 2003, 11:15:00 AM »

I've seen people saying a few things can i just clear up two points...

- it will load ANY bios now i'm using the x29477, not the BFM version but the original.
- Bioses need to be 1mb in order to work, to make it 1mb unpack the 256/512 bios with xbtool and then select file size (bottom right corner) as 1024k then repack. Rename it to xboxrom.bin / xboxrom2.bin and place it on your xbox, there you go job done.

Just make sure you have a valid eeprom code

Author Topic: Phoenix Bios Loader V1.3 (Read 1854 times)