Topic: A Lot Of Errors Explained In Detail! (Read 3969 times)

nickels · « **Reply #60 on:** March 22, 2005, 02:02:00 AM »

just a thought but the boot loading errors should have color coordination even if they are common red/green. what do i know iam trying to fix a box I BROKE. and by they way thanks for the good information.

seriouslysilly · « **Reply #61 on:** March 22, 2005, 06:10:00 AM »

QUOTE(OcnewB @ Feb 4 2004, 07:24 AM)

Ok there we go. I hope this WILL get PINNED on most (all?) of the forum sections

EAgle_47 · « **Reply #62 on:** March 28, 2005, 11:08:00 PM »

So.. what is error 13??

just kidding, great tut thx to u eh! and the other who participated to this tut (if there are any) for error 13 im going to try another way to get past through and I'll tell ya if it works

Jintao · « **Reply #63 on:** March 30, 2005, 04:24:00 AM »

ok...just so i got this straight...the only way to fix an error 9 is to get a new HD ? or is it being locked the problem ?

OcnewB · « **Reply #64 on:** April 01, 2005, 05:16:00 AM »

QUOTE(Jintao @ Mar 30 2005, 11:30 AM)

ok...just so i got this straight...the only way to fix an error 9 is to get a new HD ? or is it being locked the problem ?

Jintao · « **Reply #65 on:** April 02, 2005, 03:15:00 PM »

ok, so error 9 means there's something wrong with the HD itself ? yer explanation says something about size. would that be the size of the HD ? wouldn't make sense to me since the retail hd is only 10gb (i think/heard). any chance it could just be the model of HD i have ? it's a 40gb AT Maxtor D740X-6L. it's also several years old. might that have something to do with it ? basically, can i do anything with this HD or do i need a whole new one ? thanks.

Jintao · « **Reply #66 on:** April 04, 2005, 07:44:00 PM »

just a little bump. this thread's foundation is eroding away. eroooding, eeeerrrroooddddiiiinnnggg...

Jintao · « **Reply #67 on:** April 07, 2005, 04:12:00 PM »

bump again. seriously, this answer depends whether i spend $40, or $240

. i'd really appreciate an answer...thanks

garyopa · « **Reply #68 on:** April 07, 2005, 06:02:00 PM »

Error Code 9 - Can be only one of the three problems below:

1: Bad Hard Drive

2: Bad IDE Cable

3: Low 12volt Power

-----------------
Very Simple Solutions:

Install a new hard drive.

Try a replacement IDE cable.

Check for only 10volts on the 12volt (Yellow) cable going to the hard drive.
(If so, adjust the small pot at the front of the power supply unit, just a hair)

phatspade · « **Reply #69 on:** May 05, 2005, 09:21:00 PM »

i just had a code 9 and i found out it was caused by where the jumper was placed. make sure u have ur HD as cable select or master otherwise u get a hardware conflict since ur dvd drive is set as a slave.

Lvskapunk · « **Reply #70 on:** May 19, 2005, 04:13:00 PM »

For the error number 5, you said to boot it up with a Slayer Evox CD. Are you referring to a SlaYer's EvoX Auto-Installer? I want to make sure I turn the system on with the correct CD in as to avoid any problems.

thesideinguy · « **Reply #71 on:** June 08, 2005, 09:52:00 PM »

bump.

Reptile007 · « **Reply #72 on:** July 08, 2005, 11:10:00 AM »

I am getting a error 16, I have tryed booting off a unlocked hdd out of another xbox and still getting error 16.

I then put the harddrive from the non-working xbox into the working xbox and it booted up the the evo-x the was on the drive out of the xbox giving me the error 16.

Any ideas guys?

Thanks

thesideinguy · « **Reply #73 on:** July 13, 2005, 06:33:00 PM »

woops..

garyopa · « **Reply #74 on:** July 13, 2005, 07:07:00 PM »

QUOTE(jerunh @ Jul 6 2005, 07:30 PM)

Author Topic: A Lot Of Errors Explained In Detail! (Read 3969 times)