Post by: sdpnoy on May 13, 2004, 07:12:00 AM
Post by: lordvader129 on May 13, 2004, 07:19:00 AM
once it boots get back into evox, cut the wire(s) and flash again
Post by: sdpnoy on May 13, 2004, 07:27:00 AM
What I failed to mention was that I tried this tutorial also So you screwed up your xbox but still no go.
Post by: terrorvis on May 13, 2004, 07:55:00 AM
Oh, if 3.3v doesn't work, try 5 volts.
If that doesn't work then there is no usable code on your tsop, so a LPC mod won't work. Find yourself a 29 wire homebrew mod to fix your tsop. Personally I like the Xray3, its real cheap and only took 7 days to get from Oz to the UK, and is preloaded with m7. Or make one using the tut on the main site's tutorial section.
Post by: lordvader129 on May 13, 2004, 08:11:00 AM
Post by: sdpnoy on May 13, 2004, 08:18:00 AM
Post by: lordvader129 on May 13, 2004, 08:45:00 AM
Post by: sdpnoy on May 13, 2004, 10:06:00 AM
Post by: sdpnoy on May 13, 2004, 10:31:00 AM
You answered my questions earlier.
Post by: opjose on May 13, 2004, 03:10:00 PM
| QUOTE (lordvader129 @ May 13 2004, 04:11 PM) |
| hehe, knackered, you brits have the best slang |
Hehe.
This term always conjoured up images of coating something in enamel, to me... which made it doubly funny.
Post by: terrorvis on May 13, 2004, 11:08:00 PM
| QUOTE (lordvader129 @ May 13 2004, 05:11 PM) |
| hehe, knackered, you brits have the best slang |
You taking the mick lar?
Who says I talk funny?
Post by: sdpnoy on May 28, 2004, 08:19:00 AM
Post by: Pizza Pizz on May 28, 2004, 09:27:00 AM
deffo a v 1.0 - fan on top of heatsink & controller daughterboard
what ver slayer/evox ya using to flash?
what bios you flashing on there by chance ?
If it's a ver 1.0 then you should of been able to flash any bios nearly on there
if it was a ver 1.1 and you was using a really old slayer / bios then you could run into problems.....
Evox 2.4 don't work on ver 1.1's if my mem serves right
Older slayer discs may have used the older evox flash that didn't pad say a X2 2981 256kb to a 1mb like the recent evox's do from about 1.8.3752 or something like that
What n where did ya get the bios - the bios on slayer discs are usually quite stable, but there was a moody slayer 2.5 going around
does sound like it's trying to flash a 256kb bios into just the 1st quarter of the 1mb ST - so reconnect the wires but try and get a another slayer/evox disc with a decent working bios on it
best of luck
Post by: sdpnoy on May 28, 2004, 12:42:00 PM
Wanted to answer your questions...
It is a v1.0. I flashed it with M7. Slayers is the latest release. Unfortunately I don't remember what it was. But I've used it before on other 1.0-1.1 xbox's. I'm really stuck at this point. Kinda weird that it did work soldering a18 and a19 to 3.3 and as soon as I restart it, it doesn't work. I'm going to take it apart again...maybe the solder point came off of 3.3v. I'll try getting over to 5v...gotta find out where that's at again.
Post by: sdpnoy on June 01, 2004, 07:15:00 AM
Okay went back to see if it was the solder points and it was still there. Re-did the wiring and it booted up. Cut the wire and re-flashed it again. What's wierd is that I put my other HDD in there from my other XBox and when I try to load a game, it either goes back to EvoX or get a Dirty Disc Error. Not sure what the heck was going on there but I went ahead and ran the Slayer's install. All went well and everything. Booted it back up and now it just sits at the XBox screen. I get the logo but the logo looks all messed up like lines running through it. Get's to the part where it says "M$" and it just sits there. I think it's hosed but what do I know?
Anything else I can do or just get a new board?