Post by: iwanttheagrocrag on August 20, 2004, 03:46:00 PM
# cd ../../media/E/UDATA/4541000d/000000000000/raincoat
# ./raincoat -p xbox.bin
raincoat Flasher 0.5 Apr 14 2003 [email protected] http://xbox-linux.sf.net
Reading /etc/raincoat.conf... (unable to open /etc/raincoat.conf, using default list)
UNKNOWN DEVICE Read Only??? manf=0x09, dev=0x00
Try adding the device ID to /etc/raincoat.conf
i even added folders called etc and put raincoat.conf files in and still nothing. where is this folder? what is going on?
help would be appreciated, i also put the flash id in the raincoat and still nothing, im stumped.
Post by: trahcwolf on September 11, 2004, 06:08:00 PM
Can anyone tell me if what is listed below
shows a necessity for upgrade...?
Xecuter2_4976.02_MultiVer_256k
EvoX V2.4
EvoX D.6
EvoX D.6 EjectFix
Post by: kobe on May 23, 2003, 04:17:00 PM
The image here, shows the 2 jumper (marked in RED) points which need to be bridged. As you can see, there is no need to take the motherboard off anymore.
(IMG:http://homepage.ntlworld.com/abdul.kabir/images/xbox1_2.jpg)
You must use the latest version of raincoat 0.5 and 256k BIOS (Xecutor 4976.02 works fine)to flash the winbond chip. download raincoat 0.5
Post by: XanTium on May 23, 2003, 04:01:00 PM
I saw there are v1.2 with ST chip too now.
Post by: kobe on May 23, 2003, 07:34:00 PM
| QUOTE (XanTium @ May 24 2003, 12:54 AM) |
| Does your xbox have a winbond chip (like the picture above) or a ST ? I saw there are v1.2 with ST chip too now. |
yes its a winbond chip
Post by: skyhigh88 on May 23, 2003, 07:16:00 PM
Can v1.2 be flashed with a multibios? if so, will the old method of installing swtichs on a19, a18, gnd, and vcc will do the same for the new version? Has anyone try this before? I want to do that with my version 1.2 box if that's possible. Any info will be preciated on this topic. Thanks in advance.
Post by: PENTIUM75 on May 23, 2003, 07:19:00 PM
Post by: smokeingit on May 25, 2003, 05:07:00 PM
Flash = 0x01d5,"AMD - Am29F080B",0x100000
Flash = 0x04d5,"FUJITSU - MBM29F080A",0x100000
Flash = 0xadd5,"Hynix - HY29F080",0x100000
Flash = 0x20f1,"ST - M29F080A",0x100000
Flash = 0xbf61,"SST SST49LF020",0x40000
Flash = 0x89a6,"Sharp LHF08CH1",0x100000
Flash = 0xda8c,"Winbond W49F020",0x40000
thats the same one i have and it does not flash the TSOP. im sure you have a winbond chip but not the one in the pick.
Post by: smokeingit on May 25, 2003, 05:09:00 PM
| QUOTE (XanTium @ May 23 2003, 04:54 PM) |
| Does your xbox have a winbond chip (like the picture above) or a ST ? I saw there are v1.2 with ST chip too now. |
X, would i just have to edit the line to
Flash = 0xda8c,"ST W49F020T",0x40000
?
Post by: kobe on May 25, 2003, 06:09:00 PM
| QUOTE (smokeingit @ May 26 2003, 02:02 AM) | ||
X, would i just have to edit the line to Flash = 0xda8c,"ST W49F020T",0x40000 ? |
do u get an unknown device id, if so what is it?
Post by: smokeingit on May 25, 2003, 05:58:00 PM
unknown device
6 types read
Post by: kobe on May 25, 2003, 07:45:00 PM
| QUOTE (smokeingit @ May 26 2003, 02:51 AM) |
| manf=0*20, dev=0*B0 unknown device 6 types read |
put this code in the raincoat.conf file and give it a try
Flash = 0x20B0,"UNKOWN CHIP",0x40000
Post by: PsiDOC on May 30, 2003, 12:08:00 AM
Seeing as no one has answered your question, I will.
Yes you can back up your original bios using raincoat.
After telnet-ing in and changing the directory to where you raincoat file is, use this command.
./raincoat -r <<bios save filename>>.bin
and it will back up your flash.
Regards,
Psi
This post has been edited by PsiDOC: May 30 2003, 07:10 AM
Post by: PsiDOC on May 30, 2003, 12:22:00 AM
| QUOTE (smokeingit @ May 26 2003, 02:51 AM) |
| manf=0*20, dev=0*B0 unknown device 6 types read |
Smokeingit,
I am assuming this is the flash ID of the Newer ST 2 MB Flash that is now turning up in the 1.2's?
If so just add this to your raincoat.conf file.
Flash = 0x20B0,"ST 29F002",0x40000
And all should be well in your world.
Regards,
Psi
This post has been edited by PsiDOC: Jun 4 2003, 08:53 PM
Post by: smokeingit on May 30, 2003, 01:35:00 AM
Post by: PsiDOC on May 30, 2003, 12:39:00 PM
Have a good one.
regards,
Psi
Post by: skyhigh88 on June 01, 2003, 01:52:00 AM
I already find out how to back up my original bios with linux rc a day after my post from a buddy of mine. But, thanks again for answering my question tho.
Post by: cONEction on June 01, 2003, 10:17:00 AM
Post by: smokeingit on June 01, 2003, 12:37:00 PM
Post by: PsiDOC on June 02, 2003, 12:34:00 AM
| QUOTE (_Access @ Jun 2 2003, 09:05 AM) |
ive got probs flashing the ST tsop in a v1.2 xbox, ive flashed the winbond but i'm getting hassle with the ST  . also added Flash = 0x20B0,"ST M29F002002BT",0x40000raincoat Flasher 0.5 Apr 14 2003 [email protected] http://xbox-linux.sf.net Reading /etc/raincoat.conf... (unable to open /etc/raincoat.conf, using default list) UNKNOWN DEVICE manf=0x20, dev=0xB0 Try adding the device ID to /etc/raincoat.conf any 1 with any idea's plz |
Open raincoat.conf in notepad on your PC, add the line of text to the bottom, save it. Then ftp it back to the box.
Regards,
Psi
Post by: _Access on June 02, 2003, 03:15:00 AM
Post by: PsiDOC on June 02, 2003, 12:16:00 PM
I have posted it as a new topic >>>Here<<<
Regards,
Psi
Post by: _Access on June 02, 2003, 03:04:00 PM
...DETECTED: ST M29F002BT (256K)...thx again psi ...i'm sure this would help others as well, as there was more than me with the same problem.maybe i can invite you for tea n biscuit's
cheers
Post by: PsiDOC on June 02, 2003, 11:23:00 PM
| QUOTE |
| maybe i can invite you for tea n biscuit's |
lol Make it Beer and a Chinese take away and I'll be there
Regards,
Psi
Post by: _Access on June 06, 2003, 04:47:00 AM
Post by: PsiDOC on June 06, 2003, 05:21:00 AM
The Hynix - HY29F002 is now making an appearance in the 1.2 Box.
For those of you that have this chip, and want to use the 007 trick, then please use Raincoat 0.3 and add the following to the raincoat.conf
Flash = 0xadb0,"Hynix - HY29F002",0x40000
Psylord discovered this flash in his 1.2 Xbox, and after some furious e-mailing last night and this morning we eventually got it worked out.
Please note, Without Psylord I wouldn't have discovered this information.
Many thanks for the info.
regards,
Psi
Post by: PsiDOC on June 06, 2003, 11:29:00 AM
I am just glad we got it done, without too much fuss.
Regards,
Psi
Post by: smokeingit on June 10, 2003, 12:27:00 AM
| QUOTE (kobe @ May 25 2003, 08:09 PM) | ||
put this code in the raincoat.conf file and give it a try Flash = 0x20B0,"UNKOWN CHIP",0x40000 |
sorry kobe.... i did your method first being the one that psidoc said. i know you told me first and it totally slipped my mind to give u credit...i thought u and psidoc where the same people. my huble mistake kobe. u own!
Post by: nz87 on June 11, 2003, 06:34:00 PM
EDIT: I also wanted to note that I did the 3 jumpers that were listed in this the two on top which were shown on the first post and the one under on the first post of the second page
Post by: nz87 on June 12, 2003, 08:22:00 AM
Post by: cONEction on June 18, 2003, 07:49:00 AM
| QUOTE (smokeingit @ Jun 1 2003, 09:37 PM) |
| conection.. you do have to solder that point. |
well he says you dont have to take off the motherboard? 
Post by: cONEction on June 18, 2003, 09:28:00 AM
Post by: maltloaf on June 22, 2003, 07:27:00 AM
Flash = 0x01d5,"AMD - Am29F080B",0x100000
Flash = 0x04d5,"FUJITSU - MBM29F080A",0x100000
Flash = 0xadd5,"Hynix - HY29F080",0x100000
Flash = 0x20f1,"ST - M29F080A",0x100000
Flash = 0xbf61,"SST - 49LF020",0x40000
Flash = 0x015b,"AMD - Am29LV800B",0x100000
Flash = 0x01da,"AMD - Am29LV800B",0x100000
Flash = 0x89a6,"Sharp LHF08CH1",0x100000
Flash = 0xda8c,"Winbond W49F020",0x40000
Flash = 0x20B0,"ST 29F002",0x40000
Flash = 0xadb0,"Hynix - HY29F002",0x40000
anyone spot any errors or missing ones ??
Post by: smokeingit on June 22, 2003, 10:35:00 AM
| QUOTE (cONEction @ Jun 18 2003, 10:28 AM) |
| well i just modded a 1.2 ST and you dont have to solder under the board, so |
i dont care who says what. some people are getting there xbox killed for no reason, i asked them all about the bottom solder part and they all say the didnt short it. so i rather be on the safe side.
Post by: Pizza Pizz on June 22, 2003, 10:50:00 AM
but the bottom point was completely covered by a black sticky thingy....
started to peel it back carefully but it had a lot of tack to it and I thought fuck that if it peels up a track I won't be very happy indeed
so I just did the top 2 points - and worked like a charm - phew
was shitting meself, like I said I didn't fancy risking the bottom one if I may of ripped a track from under that black sticker thing
bloomin' shit's the life out ya it does that game save.....
fuck all for a few secs, then I turned up telly, jumped out my skin with all them gunshots then the eject light goes orange - hmmm don't panic I say config magic final does that
carried on and yup 256kb bios
WWWWWWOOOOOO HHHHHHOOOOOOOO
thanks again to all who helped with this kick-ass tutorial
007 has to be the best xbox game ever and that is without even playing it
no Xecuter 2.2 needed for me and my ST bios
thanks again - well impressed
Post by: tha_dude on June 24, 2003, 10:36:00 AM
Post by: tha_dude on June 24, 2003, 01:14:00 PM
Post by: Exobex on June 26, 2003, 06:30:00 AM
| QUOTE (kobe @ May 23 2003, 11:41 PM) |
| After 2 days of head banging ive finaly managed to flash 1.2 xbox with the Raincoat utility. I assume you you already know how to copy the raincoat files to your unmodded xbox. There are a couple of methods look elsewhere for guide. The image here, shows the 2 jumper (marked in RED) points which need to be bridged. As you can see, there is no need to take the motherboard off anymore.  You must use the latest version of raincoat 0.5 and 256k BIOS (Xecutor 4976.02 works fine)to flash the winbond chip. download raincoat 0.5 |
Kobe, are you 100% sure about the top two points? Looking at the diagrams of the underside of the board, I'd have thought the two to connect would be the two to the right of these (one of which is right on the white line around the TSOP).
Post by: Exobex on June 29, 2003, 02:16:00 AM
| QUOTE (tha_dude @ Jun 24 2003, 09:14 PM) |
| oh forget to mention i added the winbond line to raincoat 0.5 conf file still no go |
I've updated raincoat 0.5 slightly which may help, go here for more info.
Post by: cyraxx on July 07, 2003, 06:09:00 AM
| QUOTE ("mnemonico") |
| Now It tries to boot 3 times, then flash the front LED Green and RED.. and stay flashing forever... I know I´ll have to put a mod now to flash it again, but my question is, does anyone have a clue of why it didn´t work since I got no errors ??? |
I had the same problem, but I have a 1MB chip and flashed only 256KB, so I just soldered the A18 and A19 lines to GND and it worked. This shouldn't be the problem for you since your chip is only 256KB, but maybe this helps...
Post by: beer on July 10, 2003, 06:58:00 PM
| QUOTE |
| UNKNOWN DEVICE read only??? manf=0x09, dev0=00 Try adding the device ID to /etc/raincoat.conf |
I have xlinux running via the 007 exploit currently.
Is editing the raincoat.conf and then doing the HD swap the only way to update that file or can I do it via FTP
I know I can FTP to my box but, I can't login as root or upload...
Is there a seperate login....
Help
Post by: FIREitUP on July 11, 2003, 06:22:00 PM
Post by: majik655 on July 13, 2003, 11:21:00 AM
| QUOTE (nz87 @ Jun 11 2003, 07:34 PM) |
| I have a version 1.2 xbox and I am unable to flash it, I get the error message UNKNOWN DEVICE read only??? manf=0x09, dev0=00 Try adding the device ID to /etc/raincoat.conf I rechecked my points and they look good any ideas? I did not see anyone else with this error message but I could be wrong. Thanks in advance, NZ EDIT: I also wanted to note that I did the 3 jumpers that were listed in this the two on top which were shown on the first post and the one under on the first post of the second page |
I had your exact problem..
UNDO the jumper on the bottom of board.
and do the TOP of the board jumpers.. the 2 on top.
then use this raincoat that is "fixed conf file" by ebobex raincoat .501:
found here
then add this line to that raincoat.conf file:
Flash = 0x20B0,"ST M29F002BT",0x40000
then it worked like a charm flawlessly.
I do not know what chip was on it.. except I do know I got your same device id errors..
and mine was a ST so I added that line because it was the only one not in .501
I have no clue if it was needed.. but it worked great.
Post by: majik655 on July 13, 2003, 11:30:00 AM
| QUOTE (FIREitUP @ Jul 11 2003, 07:22 PM) |
| i get manufacturers ID 09 device ID 00 Flash Not Writeable!! :/ got st using the evox loader can anyone help me here? i got ST on 1.2 i did the two top jumpers and even the one on the bottom for windbond....WTF CAN I DO!? |
UNDO the bottom jumper ....
use raincoat .501 by exobex :
"Download raincoat-0.501.zip HERE , replace your existing raincoat and raincoat.conf files (the ones in your 007:AUF Linux save) with the ones in my ZIP file. "
then add this line to that raincoat.conf file :
Flash = 0x20B0,"ST M29F002BT",0x40000
then try to flash it again.
This worked for me... and hopefully for others ST
Post by: smokeingit on July 13, 2003, 03:26:00 PM
AND i even made a guide, the wonderful world of search. http://forums.xbox-s...tupid,and,guide
Post by: majik655 on July 13, 2003, 11:51:00 PM
| QUOTE (smokeingit @ Jul 13 2003, 04:26 PM) |
| Jesus... was that the problem? you never botherd to edit the conf. file? come on guys it tells you to do it from the word go on the start of this post. it was already covered and you guys didnt even bother to read it. its not a 1.2 its a 1.3 seeing that i was the one to first point it out AND i even made a guide, the wonderful world of search. http://forums.xbox-s...tupid,and,guide |
I have a question for you...
do you have to do all 3 jumpers for all the 1.2's and 1.3's ??
I ask because in your tutorial post it says to..
and others state because things or people's xbox's have shorted out only doing the 2 top ones?
I ask because in my last 2 posts on this thread I only did the top 2 and UNDID the bottom one (if it was connected properly) and everything flashed.. could I be shorting it? its a 1.2 as far as I can tell with a ST chip.
Post by: smokeingit on July 14, 2003, 01:47:00 AM
Post by: Exobex on July 14, 2003, 08:31:00 AM
| QUOTE (majik655 @ Jul 13 2003, 07:30 PM) | ||
UNDO the bottom jumper .... use raincoat .501 by exobex : "Download raincoat-0.501.zip HERE , replace your existing raincoat and raincoat.conf files (the ones in your 007:AUF Linux save) with the ones in my ZIP file. " then add this line to that raincoat.conf file : Flash = 0x20B0,"ST M29F002BT",0x40000 then try to flash it again. This worked for me... and hopefully for others ST |
There's already a line for that chip in the raincoat.conf file that comes with raincoat 0.501:-
Flash = 0x20b0,"ST - 29F002",0x40000
By adding another one you're just doubling up.
If you get the 0x00, 0x09 error, check your soldering on the point near the LPC port.
If you get "flash not writable", check your soldering on the point near the TSOP (topside or bottomside, whichever one you used).
If you can't get the solder to bridge the jumpers properly (it balls up on either side instead), you can instead tin the points and solder a single strand of wire across them, then snap off the excess (carefully) leaving you with a 3mm wire bridge.
Post by: Ikantski on July 14, 2003, 11:55:00 AM
Post by: a9h3x on July 27, 2003, 04:42:00 PM
Post by: a9h3x on August 02, 2003, 08:45:00 PM
| QUOTE (Ginie66 @ Jul 30 2003, 05:21 PM) | ||
dude try to put a switch in it might help it might not and flash the tsop 1 half at a time or try to update the raincoat to 5.0 or 5.1 that might be the prob can anyone help me put 2 switchs in so i can run 4 bioses @ 256k all i need are the points to solder with a 3 pin swith ON/ON |
you can't put a switch on 1.2 bios it's only 256k bios chip.. im going to try this with the new raincoat ill post my results.. i hope it works im pretty sure it wont seeing how that bottom trace is not connected..
Post by: Exobex on August 06, 2003, 10:16:00 AM
| QUOTE (dmozk @ Aug 4 2003, 10:26 PM) |
| I did a 1.2 ST last night. Until i bridged the bottom of the board I was getting unknown device with raincoat 3 + 5 + 5.01 Just my 2 cents |
That means you'd buggered up one of the sets of jumper points on the topside. The ones closest to the TSOP, to be precise. They're directly connected to the ones on the bottom, if you follow the tracks from the top two, they drop through two holes (one of which is on the white line surrounding the TSOP) and make a bee-line for the jumper points on the bottom side.
Post by: meokman on August 08, 2003, 07:38:00 AM
Post by: chojin on August 08, 2003, 02:44:00 PM
Post by: chojin on August 08, 2003, 04:54:00 PM
Post by: Fostbarr on August 15, 2003, 06:44:00 PM
"Flash = 0x20B0,"ST 29F002",0x40000"
will allow Rain Coat to flash a ver1.2 with ST.
And second what is the newest and best bios out to use on a 256K bios in a ver1.2 ST
thank you ahead of time for your help it is greatly apprecticed.
Post by: Geremia on August 19, 2003, 03:23:00 PM
I think that is unusefull to use raincoat.conf, because the precompiled raincoat has inside an update list of flash types and it search eventually for /etc/raincoat.conf (absolute path) and not raincoat.conf in the same dir where raincoat is lounched, so it will not load your edited raincoat.conf, unless you recompile raincoat to search in local path.
0x00 and 0x09 are the first 2 byte of all xbox bioses.
During flash identifying, pin WE and OE (do you know the 2 bridge to solder? that they are) are drived high and low in a special write sequence, the flash goes into a special status and then you read the first 2 byte that will be manufacturer and device codes, if OE and WE are not drived correctly (bad solder) you'll get simply the first 2 byte of the content of the flash.
Post by: JimmyBones on August 21, 2003, 04:28:00 AM
Post by: Moosta on September 10, 2003, 01:59:00 AM
I've got a problem. Apart from the obvious. My first experience with TSOP Flashing seems to have gone wrong some where.
I've got a Ver1.2 Xbox. I had followed tutorials with getting the 007 game save hack & raincoat configured.
All that went well. I was having troubles getting raincoat to recognise my flash chip. I downloaded and used the modified version of raincoat "raincoat 5.01". This worked fine, Detected my chip as a 256k chip ( ST-M29F002BT ) and allowed me to backup the original bios. Then I flashed it using the ( Xecuter2 - 4976.02 - 256k ) bios.
After the flash all seemed well, its went fine and completed. Then I turned the Xbox off thinking I had encountered 100% success. But then came the gut renching feeling of failure. Now when I turn it on the DVD tray wont eject. Also the eject light flickers red & green. I dont get any visual picture on the screen and no sounds either.
Does anyone know whats gone wrong ? I just keep reading about peoples success and I havent found any threads of things going wrong for anyone except raincoat not recognising the flash chip type. Could anyone shed some light on my problem ?
I've also got a thread regarding my problem here --> http://forums.xbox-s...T&f=43&t=101183
How ever I thought this may be a appropriate place for my problem too.
Any help, suggestions, feedback, comments would be appreciated.
Thanxz in advance.
Cheers
Post by: Moosta on September 12, 2003, 09:13:00 AM
Fixed my problem. Fitted a modchip.
http://forums.xbox-s...T&f=43&t=101183
Cheers
Post by: Makanic on November 10, 2003, 03:42:00 PM
Used EvoX & 007
Used Only The Top 2 Pionts
(Bottom Piont is the Same as top:)
worked sweet on
Hynix-hy29f002 Bio Ver 4977
& 2 Others.....Same Brand Tsop l Think???
HAvent gotem to Check
No Joy with
Windbond w49F020T Bio Ver 5101 or
Windbond w49F020T Bio Ver 5530
will Have to try & Use Raincoat!
Does Anyone Know if Raincoat Will Flash
Windbond w49F020T Bio Ver 5530
As with EvoX The Message l Get Is
Bio Ver "UnKnown"
Kernel Ver 1.00.5530.01
ID da Device ID 8c
2003-9-23 MFG
Do l just add ID da & Device Id 8c & where is has the Chip Name Goes eg:Hynix-hy29f002 do l add "UnKnown"
Any help would be good
Thanks in Advance
Post by: Makanic on November 10, 2003, 07:26:00 PM
Tried to flash
Windbond w49F020T Bio Ver 5530
Kernel Ver 1.00.5530.01
ID da Device ID 8c
2003-9-23 MFG
No Joy
Dead Unit Used Raincoat ,
Blanked & Copyed Bios Said it was OK...
rebooted Xbox....Flashing Red Light of DEATH...
NOt HAppy
ANyone with any Help????Post by: kard63 on November 28, 2003, 07:55:00 PM
Post by: lordvader129 on December 05, 2003, 02:22:00 PM
the jumper points are two small soldering pads, they dont look like any other points nearby
Post by: Xboxman20 on December 12, 2003, 01:54:00 PM
There is a set of jumpers on the top of the motherboard and a set on the bottom so yes you have to flly take out the mobo to do this.
Post by: maurinan on December 16, 2003, 05:54:00 AM
THX