xboxscene.org forums

OG Xbox Forums => Modchip Forums => Team Xodus Chips (Xenium) => Topic started by: Nubbs on December 22, 2006, 11:35:00 AM

Title: Solderless+xenium Ice
Post by: Nubbs on December 22, 2006, 11:35:00 AM
Alright here is what i did:

1) Took 1.0 mobo, and installed solderless adapter, and the d0, tested the xbox and everything was fine.

2) Powered down the Xbox and put on the Xenium ICE

3) Powered on Xbox and then FRAG

4) Tried a couple more times same results

5) Powered down the xbox removed the Xenium ICE, and the solderless adapter and powered back on

6) FRAG

7) FRAG

8) Tried on 2 other 1.0 motherboards with the same result with the chip and adapter, or with just the adapter or without the adapter.

Now all three mobos FRAG no matter what i try to do.

Has anyone else run into this problem? If so is there anything i can do?

Also the Xenium + Solderless combo has worked for me on numerous occasion before.

Please help.
Title: Solderless+xenium Ice
Post by: CJLee89 on December 22, 2006, 12:28:00 PM
check for lifted or burnt traces and pads. also check in the LPC for out of place marks.
Title: Solderless+xenium Ice
Post by: Nubbs on December 22, 2006, 12:35:00 PM
Do you have an example of where i could look for this? maybe a picture? lol i have never had this problem before.
Title: Solderless+xenium Ice
Post by: CJLee89 on December 22, 2006, 01:00:00 PM
i dont have one. like i dont get why they worked before you modded it and then when you take them off they still frag.

this is all i could find
Title: Solderless+xenium Ice
Post by: Nubbs on December 23, 2006, 06:37:00 AM
QUOTE(NCspecV81 @ Dec 23 2006, 12:03 AM) View Post

how exactly do you burn a trace in a solderless soltuion? =o) i think its something else.



I see no burned traces. Anyone else have suggestions?
Title: Solderless+xenium Ice
Post by: CJLee89 on December 23, 2006, 09:51:00 AM
make sure you dO is connected good. and also make sure all the connections on the LPC is connected. also, you might have lifted a trace or pad when removing the adaptor.
Title: Solderless+xenium Ice
Post by: Nubbs on December 28, 2006, 10:27:00 AM
QUOTE(CJLee89 @ Dec 23 2006, 09:58 AM) View Post

make sure you dO is connected good. and also make sure all the connections on the LPC is connected. also, you might have lifted a trace or pad when removing the adaptor.


Looks like that is what i did. When i pulled the d0 wire out i think that is the problem, because i have been trying to use a xapt3r for an xecuter on one of them and i get the same frag ....sad.gif is there any way to fix this?
Title: Solderless+xenium Ice
Post by: CJLee89 on December 28, 2006, 12:25:00 PM
this is all i could find


going to require some soldering and steady hands.
Title: Solderless+xenium Ice
Post by: Rabid1 on January 02, 2007, 12:11:00 AM
Nubbs the chances of damaging a trace while performing a solderless install are miniscule, particularly 3 times in a row. Any chance you were istalling the adapter and chip with the power still plugged in, but with the box off? Also which solderless adapter are you using?
Title: Solderless+xenium Ice
Post by: Nubbs on January 03, 2007, 12:04:00 PM
I was using the littl black Xapter.
Title: Solderless+xenium Ice
Post by: Rabid1 on January 04, 2007, 01:47:00 PM
QUOTE(Nubbs @ Jan 3 2007, 08:11 PM) View Post

I was using the littl black Xapter.

 but was the box plugged in at all? Not on just plugged in?
Title: Solderless+xenium Ice
Post by: Nubbs on January 04, 2007, 01:50:00 PM
No power at all ......