xboxscene.org forums

OG Xbox Forums => Modchip Forums => Team Xodus Chips (Xenium) => Topic started by: basic360 on August 21, 2004, 02:54:00 PM

Title: Help With Install
Post by: basic360 on August 21, 2004, 02:54:00 PM
sad.gif
Title: Help With Install
Post by: ravemonger on August 21, 2004, 02:57:00 PM
Yes you solder the 10 pads on the chip to the lpc.  I think the picture you are referring to is an example of what a good solder conenction is compared to a bad solder connection.
Title: Help With Install
Post by: ravemonger on August 21, 2004, 02:59:00 PM
In reply to your second post which just popped up....

The chip gets power and ground from the lpc bus.... on the ver 1.5 machines the power was cut from lpc bus, that's why you need to provide it from elsewhere on the board.  If you don't have a 1.5 machine, and I doubt that you do, you don't need to worry about this.
Title: Help With Install
Post by: basic360 on August 21, 2004, 03:00:00 PM
wow thanks you helped a lot i feel as if my life is in debt to you...
Title: Help With Install
Post by: ravemonger on August 21, 2004, 03:03:00 PM
biggrin.gif
Title: Help With Install
Post by: basic360 on August 21, 2004, 03:03:00 PM
also you said 10 solder points on mine i see all 10 points but on one of the the xenium doesnt have a pad next to it...just a circle about quarter millimeter away?

edit: ill paypal you 38 cents
Title: Help With Install
Post by: ravemonger on August 21, 2004, 03:05:00 PM
That's because I don't know how to count... it's 9 pads... doh!
Title: Help With Install
Post by: basic360 on August 21, 2004, 03:12:00 PM
also on the led board or whatever there are 2 ports can i plug the little cable in either one or does it matter
Title: Help With Install
Post by: phiquach on August 21, 2004, 03:19:00 PM
QUOTE (basic360 @ Aug 21 2004, 11:15 PM)
also on the led board or whatever there are 2 ports can i plug the little cable in either one or does it matter

any... don't matter
Title: Help With Install
Post by: basic360 on August 21, 2004, 03:21:00 PM
also what is that one little peice that plugs in...has a black wire and a blue prestripped on the end...and on the wire loom was i supposed to use the black wire with the ground on it...cus its just like flopping around in the air...
Title: Help With Install
Post by: ravemonger on August 21, 2004, 03:37:00 PM
The black/blue wire is optional.  you can solder the blue wire to D0 then plug the other end to the modchip.  The black is for ground, don't worry about it.

The black ground wire on the loom can be attached, just stick it under a mobo screw.
Title: Help With Install
Post by: Gumba on August 21, 2004, 10:17:00 PM
QUOTE (ravemonger @ Aug 21 2004, 11:40 PM)
The black/blue wire is optional.  you can solder the blue wire to D0 then plug the other end to the modchip.  The black is for ground, don't worry about it.

The black ground wire on the loom can be attached, just stick it under a mobo screw.

If you choose not to install the blackwire, either clip it off close to the chip, or wrap the end with electrical tape so that it doesn't short anything out
Title: Help With Install
Post by: ravemonger on August 22, 2004, 01:04:00 AM
QUOTE
If you choose not to install the blackwire, either clip it off close to the chip, or wrap the end with electrical tape so that it doesn't short anything out

Sound advice.

QUOTE
can you use the solderless adapter on the 1.6?

Off topic and no.