xboxscene.org forums

OG Xbox Forums => Modchip Forums => Team Omega Chips (DuoX) => Topic started by: antz1970 on March 06, 2005, 02:30:00 PM

Title: Duox2 White Not Boting
Post by: antz1970 on March 06, 2005, 02:30:00 PM
i would check and recheck your d0 and bt wires , also get a multimeter and try and check that you have 3.3v @point "g" on the lpc/chip , if you aint then maybe you have a v1.5 , needs an extra couple of wires to work biggrin.gif
Title: Duox2 White Not Boting
Post by: antz1970 on March 06, 2005, 03:06:00 PM
go here

and on the diagram the red line that shows 3.3v , with xbox off , select your multimeter for continuity , then put one probe on point g , and the other where the diagram shows , next to c7d3 if you get a beep or a reading from your meter then you dont have a v1.5 .(altho i still think the prob is either your d0 or bt point m8
Title: Duox2 White Not Boting
Post by: Chancer on March 06, 2005, 04:32:00 PM
Connect BT to pin 9 on the chip (G) leave the d0 on Xbox to D0 on chip. Boot the box the red led should flash on the chip. If it does flash but the regular M$ bios boots up then the D0 point is the problem. If everything boots up fine (Flash screen etc) and chip is enabled then your BT point is the original problem.
Title: Duox2 White Not Boting
Post by: HackDaBox on March 06, 2005, 05:13:00 PM
With a Duox2 you don't need a multimeter... If the red led blinks you have power and a V1.4

HackDaBox !

Title: Duox2 White Not Boting
Post by: antz1970 on March 06, 2005, 06:28:00 PM
oh ok , i didnt know that  tongue.gif
Title: Duox2 White Not Boting
Post by: HackDaBox on March 07, 2005, 12:15:00 AM
Urm i was just saying if people are worried about the version might be a V1.5  , when you install a Duox2 modchip and the red led blinks then you have power so you don't need to add any extra wires to reconnect up the power rails.

But if you have a V1.6 you don't need to worry about it and yes your chip should flash red ( i wish it was blue or something ... people allways assume red is error )

Blinking Red Is Healthy For a DuoX2 Modchip !

HackDaBox !

Title: Duox2 White Not Boting
Post by: dr_k on March 08, 2005, 12:00:00 PM
thank you all for the responses. i'm going to have night with the box today, as i was able to kick out the wife...
I'll keep you posted put if what i read is correct i might have a 1.5 and not a 1.4, and will keeping me busy as the box is modded for 1.4 right now... baaah!

dr_K
Title: Duox2 White Not Boting
Post by: dr_k on March 08, 2005, 01:26:00 PM
well, reconnected to 1.5, and the chip flashes red as it should...but...the box frags... I might check all the other connections... d0 is checked OK.

dr_k
Title: Duox2 White Not Boting
Post by: eXo on March 08, 2005, 04:13:00 PM
Well thats progress, check the wires that slave off the pins at teh bottom of the mainboard, sometimes those wreak havoc even though they look fine, just reheat them again to ensure your getting full contact.
Title: Duox2 White Not Boting
Post by: HackDaBox on March 09, 2005, 04:36:00 AM
QUOTE(dr_k @ Mar 8 2005, 08:32 PM)
well, reconnected to 1.5, and the chip flashes red as it should...but...the box frags... I might check all the other connections... d0 is checked OK.
Title: Duox2 White Not Boting
Post by: HackDaBox on March 09, 2005, 07:08:00 AM
Good pickup thanks. Must be too tired ! Anyway i have updated the pic.

BT to G !

HackDaBox !