Post by: Yo_Joe on September 22, 2005, 10:52:00 AM
all you have to do is seperate the black part and you have the orignal x-chip solderless adaptor
i feel like an idiot because how simple it is but hey i guess no one else could help me.
Post by: 82_Z28 on September 22, 2005, 11:38:00 AM
Could you give me some some specifics on what you did to get it to work?
then maybe I can write a small guide with some pics for the next bunch of people who buy the solderless adatpers...
Post by: 82_Z28 on September 22, 2005, 07:05:00 PM
(by the way if they still do please tell me where!)
Post by: Yo_Joe on September 23, 2005, 10:45:00 AM
everyone says the techs are not helping them call them on the phone thats what i did
and as far as adaptor goes the orginal x-chip adaptor is apart of the new adaptor just picture the old adaptor connected to the new one and pull it apart
i emailed you a pic z28
the part of the adaptor that is white comes off
it pulls right off and you have the 1.0-1.5 adaptor the x chip plugs in just like it always did
i hope this is helpful
also i was modding a 1.4-1.5 and it kept fraging found out it wasnt a short or a bad bios it was a bad chip so i am having to exchange for another one
Post by: 82_Z28 on September 23, 2005, 11:52:00 AM
QUOTE
doh!
thanks for the link
I will use it next time around
QUOTE
also i was modding a 1.4-1.5 and it kept fraging found out it wasnt a short or a bad bios it was a bad chip so i am having to exchange for another one
I think I may have the same situation but I'm not 100% sure yet. still testing, but at least now I'm getting the red LED on the chip (or at least until it frags)
thanks again for the pic
Post by: 82_Z28 on September 23, 2005, 12:29:00 PM
EDIT:
damnit... well XS doesn't like imageshack anymore...
if any one needs the pics e-mail me or pm me
Post by: 82_Z28 on October 09, 2005, 12:20:00 PM
The pics can be found HERE
Post by: mstreraser on October 09, 2005, 02:28:00 PM
QUOTE(Yo_Joe @ Sep 23 2005, 10:56 AM)
also i was modding a 1.4-1.5 and it kept fraging found out it wasnt a short or a bad bios it was a bad chip so i am having to exchange for another one
QUOTE(82_Z28 @ Sep 23 2005, 12:03 PM)
I think I may have the same situation but I'm not 100% sure yet. still testing, but at least now I'm getting the red LED on the chip (or at least until it frags)
I also have a 1.4-1.5 box, but I am unable to get the xbox to startup correctly after loading the bios
I do not get the xchip logo when I start up the xbox. The xbox begins to frag and i get a service error code 16 with my new 200g hard drive. I put my "loaded" hard drive from my other modded box and this one gives me an error code 5.
Any suggestions, is this just a bad chip?
Post by: 82_Z28 on October 09, 2005, 07:17:00 PM
QUOTE
I also have a 1.4-1.5 box, but I am unable to get the xbox to startup correctly after loading the bios
I do not get the xchip logo when I start up the xbox. The xbox begins to frag and i get a service error code 16 with my new 200g hard drive. I put my "loaded" hard drive from my other modded box and this one gives me an error code 5.
Any suggestions, is this just a bad chip?
I do not get the xchip logo when I start up the xbox. The xbox begins to frag and i get a service error code 16 with my new 200g hard drive. I put my "loaded" hard drive from my other modded box and this one gives me an error code 5.
Any suggestions, is this just a bad chip?
well I had my x-chip for about a year. When I started I didn't know too much about static electricity. Kind of stupid at the time. Anyway, I had replaced the adpater with the 1.6 solderless one, I got a little progress but still nothing. Then I replaced the X-Chip and it worked fine.
I might have killed it with static electricity or old age. I haven't heard how long the X-Chip is supposed to last but I'm pretty sure it was my fault.
If all else fails you may have to replace the chip like i did.
Good Luck
Post by: Daniela on January 14, 2006, 10:02:00 AM