xboxscene.org forums

OG Xbox Forums => Modchip Forums => EB2K Chips (X-Chip) => Topic started by: blinx on September 14, 2004, 03:44:00 PM

Title: Soldering D0
Post by: blinx on September 14, 2004, 03:44:00 PM

You just solder it to the top of the point. It WILL stick if you do it right. BTW wrong forums section

Title: Soldering D0
Post by: Fuzzifus on September 14, 2004, 03:45:00 PM

is the bor "lacquer" over the D0 i.e. is it green, if it is you can use a defluxing agent on it then see what you have, maybe explain what you are looking at a little more?

Title: Soldering D0
Post by: Camstheman on September 14, 2004, 04:43:00 PM

i hope you mess up cuz you put this in the wrong forum....noob

Title: Soldering D0
Post by: Camstheman on September 14, 2004, 04:46:00 PM

Newbie Chat

Title: Soldering D0
Post by: gcskate27 on September 14, 2004, 05:19:00 PM

i suggest you just solder it to the bottom... much easier...

Title: Soldering D0
Post by: drink or die on September 14, 2004, 06:09:00 PM

awww, how cute. you guys would make such a cute couple  

Title: Soldering D0
Post by: Camstheman on September 14, 2004, 06:10:00 PM

QUOTE (trentdadi @ Sep 15 2004, 01:07 AM)

He is only soldering the chip to the board because he thinks it looks cool.  Therefor, it should be considered case modding.  I think....

The board is on the inside and has nothing to do with the case.

Title: Soldering D0
Post by: investinwaffles on September 14, 2004, 06:17:00 PM

QUOTE (Camstheman @ Sep 15 2004, 02:13 AM)

The board is on the inside and has nothing to do with the case.

notice how it says Xbox Case/ HARDWARE modding...so therefore it wuld be HARDWARE MODDING U STUPID JACKASS

ya, and soldering to the bottom of the mobo is a lot easier than in the little holes on top

Title: Soldering D0
Post by: Camstheman on September 14, 2004, 06:20:00 PM

QUOTE (investinwaffles @ Sep 15 2004, 02:20 AM)

notice how it says Xbox Case/ HARDWARE modding...so therefore it wuld be HARDWARE MODDING U STUPID JACKASS ya, and soldering to the bottom of the mobo is a lot easier than in the little holes on top

NOTICE HOW THERE IS A FORUM FOR HARDWARE/TECHNICAL CHAT.

THAT WOULD BE A BETTER PLACE FOR THIS, DUMBFUCK.

AND I'M STUPID WHEN YOU CANT EVEN GET YOUR SIGNATURE TO SAY GMAIL IN RED? CHECK OUT YOUR SIG, STUPID

Title: Soldering D0
Post by: Master-Chief on September 14, 2004, 06:26:00 PM

QUOTE (investinwaffles @ Sep 14 2004, 08:20 PM)

notice how it says Xbox Case/ HARDWARE modding...so therefore it wuld be HARDWARE MODDING U STUPID JACKASS ya, and soldering to the bottom of the mobo is a lot easier than in the little holes on top

Camstheman is right... now you go invest in some more waffles, so you can get someone to solder your damn d0...  

Title: Soldering D0
Post by: Flexside170 on September 14, 2004, 06:34:00 PM

Mmmm, Waffles. Sorry, but it needed to be said and I think that this qualifies as a hardware problem suitable for either forum, but thats just my 2 cents.

Title: Soldering D0
Post by: Master-Chief on September 14, 2004, 06:46:00 PM

QUOTE (mar1no @ Sep 14 2004, 08:37 PM)

heh, god damn. installed it, its an x-chip btw, red light didnt go on. sigh, back to the workshop the front xbox lights just flash red/green haha

Don't you feel that this should be under the X-CHIP forum then?  

Title: Soldering D0
Post by: prplehz on September 14, 2004, 07:12:00 PM

Ummm last I checked the Motherboard was considered as hardware...... And wouldn't soldering a wire be hmmm, modding it maybe. Therefoe you have a hardware mod...

Title: Soldering D0
Post by: brahm2 on September 14, 2004, 07:17:00 PM

moved to x-chip chat

Title: Soldering D0
Post by: Master-Chief on September 15, 2004, 01:28:00 PM

QUOTE (mar1no @ Sep 14 2004, 09:03 PM)

no, because the topic isnt specifically about xbits, it was about soldering d0.. which i believe to be hardware modding. red light now goes on, hooray.

Moron...  

Title: Soldering D0
Post by: mar1no on September 15, 2004, 03:45:00 PM

QUOTE (Master-Chief @ Sep 15 2004, 09:31 PM)

Moron...

NIGGEROUS GOOK