xboxscene.org forums

Xbox360 Forums => Xbox360 Hardware Forums => Xbox360 General / Hardware Chat => Topic started by: mrghandi on December 12, 2009, 01:04:00 AM

Title: Fix E74, Heatgun Method Still Not Work
Post by: mrghandi on December 12, 2009, 01:04:00 AM
could someone help me with error e74

i already using heatgun n overheat method but it still show e74...
i didn't do xclamp fix, so it's original xclamp from microsoft

could someone help me with my problem
Title: Fix E74, Heatgun Method Still Not Work
Post by: xboxmods2977 on December 12, 2009, 01:14:00 AM
The ORIGINAL XBOX did not have an e74 error. If you are inquiring about the Xbox 360, your post may get more attention in the 360 section.

This post has been edited by xboxmods2977: Dec 12 2009, 09:16 AM
Title: Fix E74, Heatgun Method Still Not Work
Post by: mgeno216 on December 12, 2009, 10:59:00 AM
Reflow the GPU again and if that doesn't work try and reflow the RAM chips.  Very rarely the does it lie in the ram, but it is still possible.  If that doesn't work you may need a reball.  If it comes to that pm and i will give you the name of a good guy.
Title: Fix E74, Heatgun Method Still Not Work
Post by: mrghandi on December 14, 2009, 02:08:00 AM
QUOTE(mgeno216 @ Dec 12 2009, 07:59 PM) View Post

Reflow the GPU again and if that doesn't work try and reflow the RAM chips.  Very rarely the does it lie in the ram, but it is still possible.  If that doesn't work you may need a reball.  If it comes to that pm and i will give you the name of a good guy.



yes, I've done reflow the GPU, RAM CHIP, CHIP ANA several times, but the result is the same, still appear E74 ... I'm Indonesian, I have heatgun like this  IPB Image   What may be less hot ..??? I have been heating the GPU, RAM, ANA for about 5 minutes with the highest heat level ..... sorry my english not good
Title: Fix E74, Heatgun Method Still Not Work
Post by: under420dog on December 14, 2009, 02:57:00 AM
did you even check if the video cable was ok?
and worry more about the GPU/ANA HANA area top and bottom.....top first till you see the solder shining....
check it...then do the bottom.....make sure you let it cool at least 1/2 hour before switching fro top to bottom..

This post has been edited by under420dog: Dec 14 2009, 10:57 AM
Title: Fix E74, Heatgun Method Still Not Work
Post by: mrghandi on December 14, 2009, 03:46:00 AM
QUOTE(under420dog @ Dec 14 2009, 11:57 AM) *

did you even check if the video cable was ok?
and worry more about the GPU/ANA HANA area top and bottom.....top first till you see the solder shining....
check it...then do the bottom.....make sure you let it cool at least 1/2 hour before switching fro top to bottom..




Do I need a flux ..??? I have 3 times to heat the GPU, ANA, RAM, but the bottom was 1 time I reheat, there is another solution ..??
Title: Fix E74, Heatgun Method Still Not Work
Post by: under420dog on December 14, 2009, 04:03:00 AM
yes time for someone to go over the board and troubleshoot it...and then a re-ball as said....
Title: Fix E74, Heatgun Method Still Not Work
Post by: mrghandi on December 15, 2009, 12:49:00 AM
QUOTE(under420dog @ Dec 14 2009, 01:03 PM) *

yes time for someone to go over the board and troubleshoot it...and then a re-ball as said....


thank's for before...
after reflow the gpu, now my xbox is showing 0102, i have using the methode to fix the 0102 problem but it still didn't work!
what should i do next??
Title: Fix E74, Heatgun Method Still Not Work
Post by: under420dog on December 15, 2009, 05:12:00 AM
heat it back up....what's the temps that station puts out?
Title: Fix E74, Heatgun Method Still Not Work
Post by: mrghandi on December 15, 2009, 07:11:00 AM
QUOTE(under420dog @ Dec 15 2009, 02:12 PM) View Post

heat it back up....what's the temps that station puts out?


it's 300c max