Post by: justice91423 on April 10, 2011, 10:42:00 PM
Below is the JF log. If anyone can help I would really appreciate it.. Thanks
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~
JungleFlasher 0.1.81 Beta (226)
Session Started Sun Apr 10 20:16:13 2011
This is a 32 bit process running on 2 x 32 bit CPUs
portio32.sys Driver Installed
portio32.sys Driver Started, thanks Schtrom !
Found 4 I/O Ports.
Found 1 Com Ports.
Found 3 windows drives A: C: D:
Found 0 CD/DVD drives
Drive is Slim Lite-On..
Drive is Slim Lite-On..
0000: 05 80 00 32 5B 00 00 00 - 50 4C 44 53 20 20 20 20 ...2[...PLDS
0010: 44 47 2D 31 36 44 34 53 - 20 20 20 20 20 20 20 20 DG-16D4S
0020: 39 35 30 34 00 00 00 00 - 00 00 00 00 00 00 00 00 9504............
0030: 00 00 00 00 41 30 41 30 - 00 00 00 00 00 00 00 00 ....A0A0........
0040: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0050: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0060: 44 37 31 31 43 47 30 31 - 31 38 30 34 30 30 31 50 D711CG011804001P
0070: 55 00 00 00 U...
Sending Password to Drive on port 0xEF80
Done!
Sending Vendor Intro to port 0xEF80
Status 0x58
Re-sending Vendor Intro:
....................
Device Intro failed!
This post has been edited by justice91423: Apr 11 2011, 05:43 AM
Post by: Babilozzo on April 11, 2011, 04:44:00 AM
Otherwise is very difficult to answer or get an opinion for you problem.
Remember is always better to restart JF or OS and re-power re-plug sata I/O if you see device intro falied. But may depends of many type of hardware config, for example after device intro falied, for ME on a win seven ultimate 32, fresh install on asus pk5pl-am , just need to:
* close JF 1.81
* power off dvd drive
* unplug I/O (wait few [5-10] seconds)
* replug I/O
* repower dvd drive
* open JF
Works and unlock spi with no prob! on Native ich7 sata controller!
JF tutorials is updated , but you take a look on it?
Some people hard work on it, if read all on tut. doc., then probably found all answer you need.
Regards.
Post by: justice91423 on April 11, 2011, 04:58:00 AM
QUOTE(Babilozzo @ Apr 11 2011, 11:44 AM) 
For my opinion, you need to explain more detailed procedure to make your flash good.
Otherwise is very difficult to answer or get an opinion for you problem.
Remember is always better to restart JF or OS and re-power re-plug sata I/O if you see device intro falied. But may depends of many type of hardware config, for example after device intro falied, for ME on a win seven ultimate 32, fresh install on asus pk5pl-am , just need to:
* close JF 1.81
* power off dvd drive
* unplug I/O (wait few [5-10] seconds)
* replug I/O
* repower dvd drive
* open JF
Works and unlock spi with no prob! on Native ich7 sata controller!
JF tutorials is updated , but you take a look on it?
Some people hard work on it, if read all on tut. doc., then probably found all answer you need.
Regards.
Yes I read the tut. Yes I tried restarting the drive, and JF, and the whole PC. Yes I've tried more than once.
Post by: Babilozzo on April 11, 2011, 05:12:00 AM
QUOTE(justice91423 @ Apr 11 2011, 12:58 PM)
Yes I read the tut. Yes I tried restarting the drive, and JF, and the whole PC. Yes I've tried more than once.
Ho man!
You may try to put tray of dvd drive half open? (Power drive, eject tray, close tray with quick power off), and connect to I/O and repower ....Regards.
Post by: justice91423 on April 11, 2011, 02:08:00 PM
QUOTE(Babilozzo @ Apr 11 2011, 12:12 PM)
Ho man!
You may try to put tray of dvd drive half open? (Power drive, eject tray, close tray with quick power off), and connect to I/O and repower ....Regards.
No dice. All the other 9504s I've done have gone perfectly smooth as instructed in the JF PDF. This drive just wont unlock. Other than not unlocking it seems to work just fine (Ie plays orginal games, ejects and is detected by JF)
Post by: arana on April 11, 2011, 03:04:00 PM
but still xD
This post has been edited by arana: Apr 11 2011, 10:05 PM
Post by: trinchiuz on April 11, 2011, 03:17:00 PM
Post by: justice91423 on April 11, 2011, 03:41:00 PM
I can confirm that JF sees my drive as a 9504
Post by: trinchiuz on April 11, 2011, 03:52:00 PM
Post by: Svantesson666 on April 11, 2011, 04:06:00 PM
This post has been edited by Svantesson666: Apr 11 2011, 11:06 PM
Post by: OggyUK on April 11, 2011, 04:46:00 PM
Post by: justice91423 on April 11, 2011, 04:54:00 PM
QUOTE(Svantesson666 @ Apr 11 2011, 11:06 PM) 
Perhaps there are a few confirmed 9504 that are actually 0225's? Just like those 93850 were named 83850 (those we refer to 83850 v2). (IMG:style_emoticons/default/unsure.gif)
JF can detect what FW is on the drive. We are not just going by the label... as explained above
This post has been edited by justice91423: Apr 11 2011, 11:55 PM
Post by: arana on April 11, 2011, 07:44:00 PM
Post by: jackeroo75 on April 11, 2011, 08:19:00 PM
QUOTE(arana @ Apr 11 2011, 06:44 PM)
i also can confirm that JF sees it as a 9504
Has this XBOX been updated to the new beta dashboard?
Post by: arana on April 11, 2011, 09:00:00 PM
Post by: justice91423 on April 11, 2011, 11:25:00 PM
QUOTE(jackeroo75 @ Apr 12 2011, 03:19 AM)
Has this XBOX been updated to the new beta dashboard?
JF would not see it as a 9504 if it had
Post by: onlinepromaster on April 12, 2011, 06:40:00 AM
im just sayin, google 360 lizard and u will see greatness in regards to xbox flashing
Post by: turny on April 12, 2011, 08:05:00 AM
QUOTE(onlinepromaster @ Apr 12 2011, 12:40 PM)
its called the Lizard 360, get one, WAY WAY WAY WAY WAY WAY WAY WAAAAAAY better than the 360pro or whatever its called, shit I cant believe noone here knows this. getting mtk error? getting any error at all? need to flash any system? get a lizard, SOON WITH NO COMPUTER NEEDED< LMAO lets see 360pro do that. lets see, 50 out of 50 drives successful with lizard, about 45/50 drives successful with VIA, wowwwwww way better with lizard, less problems, less flashing time, easiest for phats, itjust makes sense all the way around, lizard toolbox = pwns jungleflasher,
im just sayin, google 360 lizard and u will see greatness in regards to xbox flashing
this is a joke, it must be.
lizard will never standalone, it currently requires pc for hitachi and slim 9504
"less flashing time" you must be kidding,
check out side by side speed tests x360usbpro wins by a mile.
"easiest for Phats" the poor chip in the lizard needs 1.8 to pmt.
hence the need for clips onto the 1.8v voltage regulator,
replacements regulators are available at lizard resellers,
I prefer not to have to replace smc unless I have to.
"lizard toolbox =pwns jungleflasher" thats not even worthy of a reply, are you serious?
This post has been edited by turny: Apr 12 2011, 03:23 PM
Post by: Svantesson666 on April 12, 2011, 03:53:00 PM
QUOTE(justice91423 @ Apr 11 2011, 11:54 PM)
JF can detect what FW is on the drive. We are not just going by the label... as explained above
But apperently TJ is already onto this, as it seems like there is a bug in JF.
Post by: OggyUK on April 12, 2011, 04:27:00 PM
QUOTE(Svantesson666 @ Apr 12 2011, 10:53 PM)
You clearly missed the point. JF identify the 83850 v2 as a 83850 and not as the 93850 it "is". Perhaps you see my point now.
But apperently TJ is already onto this, as it seems like there is a bug in JF.
We check the secret inquiry to differentiate between 83v1 and v2.
Standard inquiry isn't different.
Also, to they guy that said TB pwns JF ... So why do Maximus' team (inc vgc,) agree JF and its guide is what they aspire to. That Toolbox is for prepping fw onlt etc.
Also, with standalone you wont need toolbox, makes no sence to make it pretty
Post by: Ubergeek on April 12, 2011, 05:19:00 PM
QUOTE(onlinepromaster @ Apr 12 2011, 01:40 PM)
its called the Lizard 360, get one, WAY WAY WAY WAY WAY WAY WAY WAAAAAAY better than the 360pro or whatever its called, shit I cant believe noone here knows this. getting mtk error? getting any error at all? need to flash any system? get a lizard, SOON WITH NO COMPUTER NEEDED< LMAO lets see 360pro do that. lets see, 50 out of 50 drives successful with lizard, about 45/50 drives successful with VIA, wowwwwww way better with lizard, less problems, less flashing time, easiest for phats, itjust makes sense all the way around, lizard toolbox = pwns jungleflasher,
im just sayin, google 360 lizard and u will see greatness in regards to xbox flashing
BAHAHAHAHAHAHA
Thanks for the comedy show
lizard will NEVER be standalone for all drives. Ever. Ask them yourself
lizard is the ones causing most of the errors - how many bricks has it caused ? ever sat in their irc channel and seen how many people screwed up their drives with no help or response ?
lizard can't even badflash / unbrick without taking the dvd drive apart and using a probe - X360USB PRO does all that no problem
lizard is 20x slower than the X360USB PRo - its not even funny
ever flashed a lizard with LT+ and then done a comparison of the fw that C4E intended ? noticed any differences ?
have you seen the lizard mistakes when flashing slims ?
why does it take 4 mins just to read the DVD key on a slim (not the entire fw that X360UBS PRO does in seconds)
why are lizard / toolbox users having to redump their firmware? why do they have users that have screwed up their firmware and keys ? can toolbox fix that or is it Jungle Flasher that can fix that ?
can the lizard hack 360 HDD's
I could go on. the fact that you said toolbox pwns jungle flasher shows you are king noob of noobland which is a suburb of clueless-ville.
Enjoy a couple of comedy videos. dumbass.
Check out this X360USB PRO v Lizard Video >> http://bit.ly/egCw9d
Checkout this X360USB PRO v Lizard 9504 Slim LT+ Comparison Video >> http://bit.ly/gsZFJL
Post by: dank4life on April 12, 2011, 08:46:00 PM
they are just trying to hurt your feelings because they dont have a solution for justice91423. Funny how the same few people keep saying the same few things. You can only bully people into ignoring your defects for so long. You can continue to deny rationalize and make excuses for so long until it becomes obvious you are compensating for something. Make no mistake people. the adolescents who made the previous comments are members of the joint jungle flasher/ xecuter team. They made no attempt to offer support for their product, except for to refer to some piece of "no eta" vaporware. They then procedeed to shift the focus from the problem and go offtopic whining & teasing. Good job junglebunnies.
You still never answered the question.
Why is your software reporting an 0225 as a 9504 when you claim to be doing a full dump?
is it a glitch?
is it broken?
or is "Lizard sux0rz" your final answer to the 3 users in this thread who arent even talking about the lizard?
Post by: OggyUK on April 13, 2011, 12:48:00 PM
I'll be sure to reply, in full, later.
JF sees a drive for what it inquires as... Exactly as the xbox360 does. There is no bug.
What JF shows in Port Properties is exactly what its being told by the drive, this is how spoofing works/worked.
Post by: pure_bluff on April 13, 2011, 01:10:00 PM
Post by: boneym on April 13, 2011, 01:26:00 PM
a man who married a sex kitten just as she turned into a cat.
a man who moved into the smart money
just as the smart money moved out.
a man who chose max when he should have chose tx.
Post by: podger on April 14, 2011, 07:57:00 PM
Are you still getting status 0x58 ?
Post by: justice91423 on April 15, 2011, 02:51:00 AM
QUOTE(podger @ Apr 15 2011, 02:57 AM)
justice91423: is this topic still open ?
Are you still getting status 0x58 ?
Yes. I have the same results even with JF 1.82.
Post by: podger on April 15, 2011, 03:15:00 AM
0x58 means the drive is asserting DRQ.. meaning it has or wants data... This is because the code c4 added to sector 3e000, uses the unlock routine in a modified way to read the flash... So basically, if your first attempt failed before the 3e000 sector was restored then the Unlock routine will not be unlocking but actually requesting a flash dump....
Soooo, C4 added an unlock of his own in the modified state. This can be accessed using the key combo ctrl + shift + f9. So:
1. power cycle the drive,
2. ctrl + shit + f9
3. click intro ... should just work and give device ID ( money is on it being winbond)
4. load your CFW or OFW and click write, with the new delays added in 1.82, it should work fine first go..
//
This post has been edited by podger: Apr 15 2011, 10:19 AM
Post by: justice91423 on April 15, 2011, 04:08:00 AM
QUOTE(podger @ Apr 15 2011, 10:15 AM)
We can sort this now..
0x58 means the drive is asserting DRQ.. meaning it has or wants data... This is because the code c4 added to sector 3e000, uses the unlock routine in a modified way to read the flash... So basically, if your first attempt failed before the 3e000 sector was restored then the Unlock routine will not be unlocking but actually requesting a flash dump....
Soooo, C4 added an unlock of his own in the modified state. This can be accessed using the key combo ctrl + shift + f9. So:
1. power cycle the drive,
2. ctrl + shit + f9
3. click intro ... should just work and give device ID ( money is on it being winbond)
4. load your CFW or OFW and click write, with the new delays added in 1.82, it should work fine first go..
//
First off, thank you very much for helping.
I followed your steps and it did unlock the drive (status 72). However I dont have the OFW since I was never able to unlock the drive. Instead I clicked READ for step 4. JF came up with unknown f/w !. At which point I had an hourglass cursor so all I could do was exit.
Log and screen shot below.
Any help is appreciated
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~
JungleFlasher 0.1.82 Beta (234)
Session Started Fri Apr 15 01:53:25 2011
This is a 32 bit process running on 2 x 32 bit CPUs
portio32.sys Driver Installed
portio32.sys Driver Started, thanks Schtrom !
Found 4 I/O Ports.
Found 1 Com Ports.
Found 3 windows drives A: C: D:
Found 0 CD/DVD drives
Sending Vendor Intro to port 0xEF80
Serial flash found with Status 0x72
Sending Device ID request to port 0xEF80
Spi Status: 0x0
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Getting Status from port 0xEF80
Serial flash found with Status 0x72
Reading Drive Key.
Authorised !
............Confirming sector 0x3E000.
................
Unknown f/w !
(IMG:http://i52.tinypic.com/x0tukx.jpg)
Post by: podger on April 15, 2011, 04:15:00 AM
BUT
if ctrl + shift + f9 worked its certain JF has been here before..
try this
1. Power cycle
2. ctrl + shift + f9
3. Slimkey
4. *** say NO ***
5. should intro and grab key etc and save a dummy.bin
//
Post by: justice91423 on April 15, 2011, 04:21:00 AM
QUOTE(podger @ Apr 15 2011, 11:15 AM)
OK, I'm not entirely sure where it went wrong on the first attempt..
BUT
if ctrl + shift + f9 worked its certain JF has been here before..
try this
1. Power cycle
2. ctrl + shift + f9
3. Slimkey
4. *** say NO ***
5. should intro and grab key etc and save a dummy.bin
//
Well that worked. I'm hesitant to flash it since I'm not doing a full FW read and someone has been poking around this drive before me. Any thoughts on risks?
Post by: podger on April 15, 2011, 04:34:00 AM
not sure what you mean "someone", as you have not really mentioned the circumstances under which the drive arrived with you...
Obviously if you have a spare 9504 handy, you could flash that and test..
if not.... well
does the Key "look" ok, as in, no multiple 0x00, 0x77, 0xff, 0x5A etc
was there any message during the extract that would lead you to believe it didn't go swimmingly ??
if you load the dummy as source and LT as target, spoof, does the target key verify ??
Does the drive play games now ( unlikely on latest dash in any case with 3e000 modified )....
In source "Serial" tab, does the barcode on line 1 match the barcode on the drive label...
//
This post has been edited by podger: Apr 15 2011, 11:35 AM
Post by: justice91423 on April 15, 2011, 04:50:00 AM
Thanks for all your help.
Post by: podger on April 15, 2011, 06:19:00 AM
good news.... just a pity it took so long getting it all sorted...
This post has been edited by podger: Apr 15 2011, 01:20 PM
Post by: Ubergeek on April 23, 2011, 03:26:00 PM
Post by: ruben182 on May 28, 2011, 06:53:00 AM
QUOTE(podger @ Apr 15 2011, 11:15 AM)
1. Power cycle
2. ctrl + shift + f9
3. Slimkey
4. *** say NO ***
5. should intro and grab key etc and save a dummy.bin
//
What do you mean with step "3. Slimkey" ?
Thanks to ctrl + shift + F9 I finally seem to be able to intro.
But when I read I always get "Unknown f/w!"
Post by: Rammieone on May 28, 2011, 06:59:00 AM
QUOTE(ruben182 @ May 28 2011, 01:53 PM)
What do you mean with step "3. Slimkey" ?
Thanks to ctrl + shift + F9 I finally seem to be able to intro.
But when I read I always get "Unknown f/w!"
Using the latest Jungleflasher there should be a tab button saying SlimKey hit that at step 3 mate
Here you go mate
Post by: ruben182 on May 28, 2011, 07:13:00 AM
QUOTE(Rammieone @ May 28 2011, 01:59 PM)
Using the latest Jungleflasher there should be a tab button saying SlimKey hit that at step 3 mate
Here you go mate
Haha! Thanks for the super fast reply!
I was looking in the MTK Flash tab
Everything worked perfect!
Other question: Should I be able to do a full dump with only my Maximus Xtractor? Or is this only possible with this Slimkey dump?