xboxscene.org forums

Xbox360 Forums => Xbox360 Software Forums => PC Tools and Utilities (Xbox 360 related) => Topic started by: out4it on October 05, 2006, 03:42:00 PM

Title: Flashing A Sammy Drive
Post by: out4it on October 05, 2006, 03:42:00 PM
QUOTE(sandog @ Oct 5 2006, 05:23 PM) View Post

trying flash my drive get it to boot in too dos but when i type in samread in the video there saying there is 13 care for my serial numer i only see 10 on my drive so when i type that command it says ....port info master slave A0 in ideas why i'm stuck here...


Yes,there are 13. Not on drive,but on front of xbox near usb lid.
Title: Flashing A Sammy Drive
Post by: sandog on October 05, 2006, 04:00:00 PM
Got the number ...but still geting the port info master/slave  AO thing when I type samread ..........
Title: Flashing A Sammy Drive
Post by: Klutsh on October 05, 2006, 04:13:00 PM
If you have a MS28 Drive you need the VCC or 10 Second Trick to get it to work.

10 Second Trick needs a VIA SATA card.
VCC need's soldering.
Title: Flashing A Sammy Drive
Post by: sandog on October 05, 2006, 04:22:00 PM
I think I have a 25 drive....... it says FW=ms25 so let me know if that is it ...or how can you tell
Title: Flashing A Sammy Drive
Post by: Klutsh on October 05, 2006, 04:35:00 PM
You do have MS25.

Have or do you need to edit MTKFlash for your SATA chipset?
Title: Flashing A Sammy Drive
Post by: sandog on October 05, 2006, 04:47:00 PM
Yes i did I have a asus motherboard with built in sata I'm useing MTKFlash with this NVIDIA nForce 590/570/550 Serial ATA Controller useing the detect ID  botton to find my ID and port and it finds them.
Here is the link to my motherboard http://www.asus.com/...amp;modelmenu=1
Title: Flashing A Sammy Drive
Post by: sandog on October 05, 2006, 07:48:00 PM
GOT IT.................. Thanks for all the help....
Title: Flashing A Sammy Drive
Post by: nsfdheo on October 05, 2006, 07:59:00 PM
I had a tough time flashing the MS25 also. We went to newegg.com bought the prefered SYBA SY-VIA-150R PCI SATA /IDE Combo RAID Controller Card RAID for $14.99 (the 9.99 one was out off stock). Flashed it the 520c Via drivers (I think). Then used the edited MTKFlash for the Via chip set with the  Samread v4. I had to edit the Samremod.edit and Samread.batch files and change the name from extreme v32 to v33. ( All i did was delete the 2 and change it to a three in both those files.) I did this because I wanted the newest firmware. Or you could just put in the 32 version and eliminate the changes. I tried this on my emachine (for hours and hours) but and couldn't get it to work. Then tried it on a dell pc and it worked just fine. i didn't even need to unplug the ide drives from the motherboard. Only the sata cable pluged into the back sata port on the card. (zero I think)  after this the drive showed up in the Mtkflash section. hope this helped biggrin.gif



great to here  pop.gif
Title: Flashing A Sammy Drive
Post by: Klutsh on October 05, 2006, 09:41:00 PM
QUOTE(sandog @ Oct 6 2006, 02:55 AM) View Post

GOT IT.................. Thanks for all the help....

What did you do to fix it?
Title: Flashing A Sammy Drive
Post by: sandog on October 06, 2006, 03:21:00 PM
I Think my problem was i had my sata pluged in sata 1 slot...I had it in number 4