xboxscene.org forums

Xbox360 Forums => Xbox360 Hardware Forums => Xbox360 Backup Forum - DVD DL help / ISO Building => Topic started by: tomgreen99200 on November 09, 2011, 04:13:00 PM

Title: Burning Cod Mw3 Using Ixtreme Burner Max
Post by: tomgreen99200 on November 09, 2011, 04:13:00 PM
No you shouldn't be getting that error message if you truly have a iHAS1124b with LT MAX. Make sure you are using the latest version of Imgburn.
Title: Burning Cod Mw3 Using Ixtreme Burner Max
Post by: IDONTuseKYJELLY on November 10, 2011, 12:46:00 PM
Make sure you flashed your drive correctly with the IMAX Burner Firmware, and as he said above.
Title: Burning Cod Mw3 Using Ixtreme Burner Max
Post by: Gokussj5okazu on November 10, 2011, 12:52:00 PM
Just for shits and giggles, use Flash Util. to revert to your stock firmware, then crossflash it to a iHAS324, THEN flash with iXtreme. That should work perfectly, as I did mine that way.
Title: Burning Cod Mw3 Using Ixtreme Burner Max
Post by: cheapjeep78 on January 10, 2012, 10:31:00 PM
I have the same setup but get a full burn but always a unrecognized disc.
Ihas124b flashed with burner max
Benq 0800
Verbatim mkm 001 @ 2.4
Latest imgburn
Agbx verified
Hitachi 46 & 47 both give unrecognized disc
Running lt 3.0
All old backups work great but no xdg3.
Any help would be appreciated.
New to the forums so email if I don't respond often. Thanks
Title: Burning Cod Mw3 Using Ixtreme Burner Max
Post by: bbcorvette2000 on January 12, 2012, 03:40:00 AM
QUOTE(cheapjeep78 @ Jan 10 2012, 11:31 PM) View Post

I have the same setup but get a full burn but always a unrecognized disc.
Ihas124b flashed with burner max
Benq 0800
Verbatim mkm 001 @ 2.4
Latest imgburn
Agbx verified
Hitachi 46 & 47 both give unrecognized disc
Running lt 3.0
All old backups work great but no xdg3.
Any help would be appreciated.
New to the forums so email if I don't respond often. Thanks


Have you tested your backups with kprobe or Nero speed? Even though the media is good, the burn quality could be bad. I used MKM001's as well and achieved the best results burning at 4x (score of 95 on NeroSpeed) with the following settings.

EEPROM: enable all except for OHT (disable) clear OPC    (also make sure to power cycle drive to make changes effective)

IMGBURN: OPC off, burnproof off
Title: Burning Cod Mw3 Using Ixtreme Burner Max
Post by: tim132 on January 18, 2012, 08:10:00 AM
QUOTE(cheapjeep78 @ Jan 11 2012, 05:31 AM) View Post

I have the same setup but get a full burn but always a unrecognized disc.
Ihas124b flashed with burner max
Benq 0800
Verbatim mkm 001 @ 2.4
Latest imgburn
Agbx verified
Hitachi 46 & 47 both give unrecognized disc
Running lt 3.0
All old backups work great but no xdg3.
Any help would be appreciated.
New to the forums so email if I don't respond often. Thanks


I would say this is due to a weak laser, XGD3 backups are known to be harder to read than XGD2 and originals. You could try a pot tweak or install a new laser. I would go for the pot tweak first, solved my problems in the past!