xboxscene.org forums

Xbox360 Forums => Xbox360 Hardware Forums => Xbox360 Backup Forum - DVD DL help / ISO Building => Topic started by: jabroniekilla on March 15, 2007, 07:56:00 AM

Title: Xp Locking Up With Enable0800.iso
Post by: jabroniekilla on March 15, 2007, 07:56:00 AM
couple things to try:  leave the tray open while booting pc, also, I had to put my pc's hdd on the second sata port and my 360 on the 1st sata port or else it would freeze.  I dont know if this helps but its worth a try.
Title: Xp Locking Up With Enable0800.iso
Post by: lfielder on March 15, 2007, 09:28:00 AM
eject the drive a few times during the xp boot screen. I have heard this helps. I also have a ms28 and have had no problems doing exactly as you say, but I burned 0800.iso on a dvd-r and it still works fine.
Title: Xp Locking Up With Enable0800.iso
Post by: strelor on March 15, 2007, 11:55:00 AM
QUOTE(lfielder @ Mar 15 2007, 11:35 AM) View Post

eject the drive a few times during the xp boot screen. I have heard this helps. I also have a ms28 and have had no problems doing exactly as you say, but I burned 0800.iso on a dvd-r and it still works fine.

while ejecting the 360 freezes right when xp freezes...going to try to burn th 0800 to a dvd-r and see

system specs
AMD athlon 64 3200+
2ghz ddr ram
A8N-SLI motherboard with sata nforce4 chip
VIA VT6421 (for flashing, when 360 is hooked up to this the comp also freezes at xp boot up)
sata maxtor 6B160M0 hdd
Title: Xp Locking Up With Enable0800.iso
Post by: strelor on March 15, 2007, 12:47:00 PM
still no go with the DVD-R.  Tried safe mode tried putting the 360 and pc HDD on all differnet kinds of combinations of sata ports...Tried with tray open/closed, disk in disk out, Do i have a hardware compatibility problem?  Or do i need to flash with the 0800.bin?  If i need to flash with the bin i think i will move on to another method for backups.  Or maybe this Mother board, seeing as it has a weird bios, needs some special bios setting?
Title: Xp Locking Up With Enable0800.iso
Post by: strelor on March 15, 2007, 01:36:00 PM
QUOTE(strelor @ Mar 15 2007, 09:21 AM) View Post

I have a samsung flashed and working just fine.  I flashed with xtrem52b.  I tried today to hook up my drive to my pc using the enable0800.iso method.  My bios detects the drive but when XP goes to boot the pc freezes and I have to restart my pc.  So far I have looked around and seen a few things about flashing the drive with a 0800.bin to make backups.  Do I have to do this or is there another way to get the enable0800.iso to work?
*samsung is a ms28 playing normal games just fine, have not tried backup one due to XP locking up
*used verbatim dvd+dl for enable 0800.iso burn
*power on 360 first let it read disk then eject disk and power on PC
*pc gets to XP boot up screen and feezes

anyone know what i should do?


FIXED just needed to install the 5.2 drivers for VIA sata controller and plug the 360 into that....PERFECTION
thanks for all the help.
Title: Xp Locking Up With Enable0800.iso
Post by: timewaster on March 16, 2007, 06:57:00 AM
QUOTE(strelor @ Mar 15 2007, 02:43 PM) View Post

FIXED just needed to install the 5.2 drivers for VIA sata controller and plug the 360 into that....PERFECTION
thanks for all the help.


Can you post the link on where you got the 5.2 drivers?
I have a similar problem. ms28 drive with a VIA 6421A sata card.
When my computer boots up during the bios check, the card reports an error.
I do not even get to the point where it tries to boot to windows.
I was able to flash with the card with no problems.
Title: Xp Locking Up With Enable0800.iso
Post by: sosotiit on March 16, 2007, 08:14:00 AM
in here

rgds,soso