xboxscene.org forums

Xbox360 Forums => Xbox 360 Hacking Forums => Technical DVD-ROM and Modified DVD Firmware Forum => Topic started by: 360newb22 on August 12, 2009, 12:49:00 PM

Title: Dump From 83850c Doesn't Look Right? (jf.log Included)
Post by: 360newb22 on August 12, 2009, 12:49:00 PM

OK I just tried to dump a stock 83850C and I don't know if it went well or not.  I had previously soldered the necessary points for the old liteons and tried to dump it as if it was an old model without luck.  I then realized it was a 83850C so I removed the solder bridges and went about dumping it using DOS and lo83info.exe.  This seemed to go well, as it did not report any errors.  From there I ran the file through Freekey and it also did not report any errors and returned a non-null key, although I don't know whether the key was good or not.  As a saftey measure I just tried to dump it again using Jungleflasher 1.65b.  Again, things seemed normal as no errors were reported, however I did not see the "In Dedication to" portion.  My guess is that the dump wasnt successful, but I can't think of why.  I am using a 360 Xtractor to power the drive, and I have removed the solder bridges from the drive.  Is it possible that I need to rebridge the solder points?  Also, is it possible that when I tried to dump it the first time with the points bridged using dosflash and the 360 Xtractor reader that I messed the drive up?  Here is the JF.log:

CODE

 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~

JungleFlasher 0.1.65 Beta

Session Started Wed Aug 12 16:36:01 2009



This is a 32 bit process running on 2 x 32 bit CPUs

PortIO is installed and running.

Found 6 I/O Ports.

Found 1 Com Ports.

Found 5 windows drives A: C: D: E: F:

Found 1 CD/DVD drives E:



Sending LO83info request to I/O port 0xD820



........................

..........

0000: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

0010: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

0020: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

0030: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

0040: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

0050: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

0060: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................



0000: 05 80 00 32 5B 00 00 00 - 50 4C 44 53 20 20 20 20 ...2[...PLDS    

0010: 44 47 2D 31 36 44 32 53 - 20 20 20 20 20 20 20 20 DG-16D2S        

0020: 38 33 38 35 30 43 41 30 - 41 32 44 36 30 39 43 47 83850CA0A2D609CG

0030: 39 32 31 39 31 33 30 30 - 4D 42 57 20 20 20 00 00 92191300MBW   ..

0040: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

0050: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................



Inquiry String saved to F:\Liteon 83850c\b west JF dump\Inquiry.bin



0000: 44 36 30 39 43 47 39 32 - 31 39 31 33 30 30 4D 42 D609CG92191300MB

0010: 57 20 20 20 FF FF FF FF - 39 45 31 34 31 38 39 30 W   ....9E141890

0020: 31 36 44 36 31 34 58 58 - 41 30 FF FF 53 34 50 39 16D614XXA0..S4P9

0030: 35 31 32 30 30 30 30 30 - 30 35 38 32 36 33 00 00 51200000058263..

0040: FF FF FF FF FF FF FF FF - FF FF FF FF 41 32 FF FF ............A2..





Extraction file saved to F:\Liteon 83850c\b west JF dump\D609CG92191300MBW.bin

This post has been edited by 360newb22: Aug 12 2009, 08:09 PM

Title: Dump From 83850c Doesn't Look Right? (jf.log Included)
Post by: NA_0815 on August 12, 2009, 01:08:00 PM

how about readin a manual?
check the key by usin freekey.there is a new version out now because the wrong-key-bug in version 1.0
so everything should be fine..no soldering needed etc...

Title: Dump From 83850c Doesn't Look Right? (jf.log Included)
Post by: glent1234 on August 12, 2009, 01:26:00 PM

make sure you have the latest version of freekey or openkey. I had to use dos to get a valid dump as Jf wouldnt work for me

Title: Dump From 83850c Doesn't Look Right? (jf.log Included)
Post by: 360newb22 on August 12, 2009, 01:38:00 PM

QUOTE(NA_0815 @ Aug 12 2009, 03:08 PM)

how about readin a manual?
check the key by usin freekey.there is a new version out now because the wrong-key-bug in version 1.0
so everything should be fine..no soldering needed etc...

Could you be more specific?  Look at the log from JF1.65b.  I used the "JungleFlasher 0.1.65b LiteOn '83850c' Guide" in the PDF on this forum.  I took the bin file I got from there and ran it through Openkey 0.2 and it said the key is blank.  Is it possible that when I tried to dump the key from it using the methods for old Liteons I ruined the key?  

I initially soldered the R707 and R708 (I know only R707 is required, but I have always done both since the early Liteon days) and tried to dump the drive with dosflash.  When that didn't work I tried to do it in Xtractor Reader 2.6 and that also failed.  From there I checked the drive case and saw it was a 83850C.  Upon this discovery I removed the solder bridges, and I used l083info in DOS to dump it, and then Jungleflasher 1.65b also.  Both seemed to run without errors, but in neither did I see the "In Dedication To" message.  However when I ran Freekey (not sure what version) on the bin from lo83info I got:

52 4B D5 3F F4 84 F8 65 DD 7B C8 0A 9E 5B 74 0D

UPDATE:

Ok, thanks to all for your help!  I just tried the initial dump that I got from DOS with Openkey v2 and I saw the "In dedication to" message and it returned a valid key and saved the bin.  Thanks for all of your help!  Now I need to build the new FW and flash it.  Another n00b question though, I have been seeing stuff about iX1.6 for 83850C and iX1.6 for 7 series Liteons.  Is this a totally separate CFW?

Thanks as always!

Title: Dump From 83850c Doesn't Look Right? (jf.log Included)
Post by: OggyUK on August 12, 2009, 05:24:00 PM

Yes it is.

Title: Dump From 83850c Doesn't Look Right? (jf.log Included)
Post by: sancho_panza on August 14, 2009, 10:57:00 AM

QUOTE(OggyUK @ Aug 13 2009, 01:24 AM)

Yes it is.

Yes that dump is WRONG!