Print Page - Lite-on Hell Help Plz

Xbox360 Forums => Xbox 360 Hacking Forums => Technical DVD-ROM and Modified DVD Firmware Forum => Topic started by: gopher2005 on December 27, 2008, 06:39:00 PM

Title: Lite-on Hell Help Plz
Post by: gopher2005 on December 27, 2008, 06:39:00 PM

hi guys ok my liteon froze during erasing with via card,after reading threads on the forum im trying dosflash in dos on iprep,iv copied all files and my lite-cfw.bin every time i run l-o-eras i get status ff7f? i dont think its detecting the drive at all my port number is correct iv power cycled loads of times i think the drive is dead any suggestions? (IMG:style_emoticons/default/uhh.gif)

Title: Lite-on Hell Help Plz
Post by: woody21_1 on December 27, 2008, 06:43:00 PM

have you tried running l-o-eras several times without power cycling the pc or drive , if you still cant get the correct status try flashing anyway and see.

Title: Lite-on Hell Help Plz
Post by: gopher2005 on December 27, 2008, 06:46:00 PM

i cant flash tho cuz when i type dosflash and hit enter no drives are detected,iv also tryed booting with 360 powered off and powering on straight after hiting enter on dosflash?

Title: Lite-on Hell Help Plz
Post by: tewy on December 27, 2008, 06:50:00 PM

have u used the flash with jungleflasher in windiows turorial thread on these forums the 1 that describes unstalling via drivers and adding new divice the portio32 i will try to find link cos i used via 8*** not to sure which and jungle flasher ran fine hope this helps

Title: Lite-on Hell Help Plz
Post by: woody21_1 on December 27, 2008, 06:58:00 PM

try powering up the 360 drive at the same time as your pc as well just in case your sat1 isnt recognising it.

is the tray still in the half open position, i dont know if it matters but i leave it like that from when i read the key till i have sucesfully flashed

my via vard can be touchy about returning the correct status but usually the second attempt at erasing it goes and i have got dosflash to pick it up by retying that and tryin yes and no to resending mtk codes question. i flash using the dosflash package thas included in the ix15 package and read the key with jungleflasher

there has been a newer version of dosflah32 relesed siince the firmware, you could try that or jungleflsher with port io drivers properly installed as suggested.

Title: Lite-on Hell Help Plz
Post by: tewy on December 27, 2008, 07:00:00 PM

cant find link but is called N00B_LiteOn_Flash_with_VIA i follow that and also found this in a thread (press liteon erase then on the second yes box i switched the drive off then pressed yes and immediately afterwards turned the drive back on) hope this helps
i have a copy of tut but not sure how to post it

This post has been edited by tewy: Dec 28 2008, 03:02 AM

Title: Lite-on Hell Help Plz
Post by: gopher2005 on December 27, 2008, 07:13:00 PM

thanks i found the tutorial,will give it ago and let you no

Title: Lite-on Hell Help Plz
Post by: dpbmt on December 27, 2008, 07:30:00 PM

keep sending the command till you get FF72, can take a few tries.

Title: Lite-on Hell Help Plz
Post by: gopher2005 on December 27, 2008, 07:48:00 PM

QUOTE(dpbmt @ Dec 28 2008, 05:06 AM)

keep sending the command till you get FF72, can take a few tries.

ok iv sent command about 50 times always ff7f,so to confirm if it was my via card i hooked up a sammy drive out of my other console and dosflash detects it? so i hotswaped the drives with l-o-eras get status ff80 so i tryed liteon e in dosflash command and said it sucsessfuly erased the drive so tryed l-o-eras again but still ff80 tryed flashing but get unknown flash error,im struggling on mtk intro as i cant power drive off and on quick enough?

Title: Lite-on Hell Help Plz
Post by: gopher2005 on December 27, 2008, 09:21:00 PM

also do i need my max232 serial conected to erase and flash as iv been told i dont need it although i have been trying with it conected?

Title: Lite-on Hell Help Plz
Post by: nitussi on December 28, 2008, 04:05:00 AM

I got the same problem, did all this work for nothing, including making the circuit to get the key. After that long process of researching and soldering resistors, i get all the way up to erasing the chip in dosflash16, and now I got a dead drive and a usless 360. My sata port does not even recognize the drive anymore. This sucks.

Title: Lite-on Hell Help Plz
Post by: tewy on December 28, 2008, 05:26:00 AM

i am 100% sure once erased it didnt see my drive in windows and in jflasher the drive details al came up as mymymymymymy but i pressed write and it worked,i thought i had toasted mine as it wouldnt eject or any thing

Title: Lite-on Hell Help Plz
Post by: nitussi on December 28, 2008, 06:09:00 AM

I figure it out and fixed my somewhat brick drive.

This is what I do to flash. I did a second 360.

Put the drive back together because you dont need it open anymore after retreiving the key.

Boot dos off a usb thumb drive that has dosflash, hacked.bin(CFW_lite.bin) and L-O-erase on the root.

Typed dosflash to get port address of the drive.(Already knew it from retrieving key earlier)

Hit 'Ctrl+c' to get out of dosflash.

Typed 'L-O-erase E080'(E080 is the port for the drive)

It erases, I got FF07(guess that means it erases)

Then I erased it a second time to make sure and got another funky number. You know the drive is erased when it wont eject.

Turned power to the drive off, then back on again(the drive is dead)

Typed dosflash. It did not see the the drive, but I typed the port that I knew the drive was on anyway.

It asked me what I wanted to do so I typed a 'w' for write.

Then it asked me for the file. I typed my file which was 'hacked.bin'. Dont forget to put '.bin' like I did a few times.

Then it proceeded to erase and wrote all four banks.

I dont know if you can skip l-o-erase and just use dosflash and type 'w', but i will try on my next 360. But i know for sure that l-o-erase comepletly erased my drive and allowed dosflash to work on what I thought was a bricked drive.

This post has been edited by nitussi: Dec 28 2008, 02:11 PM

Title: Lite-on Hell Help Plz
Post by: brisk on December 28, 2008, 06:14:00 AM

QUOTE(gopher2005 @ Dec 28 2008, 03:15 AM)

try this

http://www.tiaowiki.com/wiki/index.php?tit...Troubleshooting

Title: Lite-on Hell Help Plz
Post by: arjunanand1 on December 29, 2008, 12:55:00 AM

I got my key and made the hacked firmware easily with xtractor + jungleflasher. But after an erase attempt, things went haywire. I tried dosflash which fixed everything (IMG:style_emoticons/default/smile.gif).Btw, its to be noted that my drive would not respond to eject attempts, here's what I did:

1) Open iprep, create bootable disk for benq (yes, benq).
2) Open usb key, remove unneeded benq files, copy on the dosflash, L-O-Eras, DosFlash.typ and Lite_CFW.bin(Hacked lite-on firmware made with jungleflasher).
3) Reboot pc and disconnect xtractor kit (or whatever you have) from molex and reconnect everything again.
4) Select your usb key from the boot menu and let it load up.
5) Type in l-o-eras XXXX, where XXXX is your SATA port, example: EC00.
6) Repeat command until you get the status: 00x72, this indicates that it is erased. You may need to try this command a few times (TIP: Hold F1 so that command is re-written automatically)
7) type dosflash, read on screen instructions. Use the w command to write, it will then ask you for the firmware filename.
8) My hacked firmware is called lite_cfw.bin so I type this in and it writes all 4 banks.

Success (IMG:style_emoticons/default/biggrin.gif)

xboxscene.org forums

Xbox360 Forums => Xbox 360 Hacking Forums => Technical DVD-ROM and Modified DVD Firmware Forum => Topic started by: gopher2005 on December 27, 2008, 06:39:00 PM