xboxscene.org forums

Xbox360 Forums => Xbox 360 Hacking Forums => Technical DVD-ROM and Modified DVD Firmware Forum => Topic started by: techmob on May 08, 2008, 04:32:00 AM

Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: techmob on May 08, 2008, 04:32:00 AM
QUOTE(Kotana @ May 8 2008, 12:03 PM) View Post

BenQ flashing     everything was god, no erros or something like this...
Please help me...
Wat can i dooooooo...
I have the backup form the orig.bin
Sorry for my bad englisch


check that the drive key is ok in the orig.bin with 360FW-Toolbox-46 and also check the custom firmware to see if the key is ok in that

key might be the problem  sleep.gif
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: Kotana on May 08, 2008, 04:53:00 AM
ok thanks

how can i see the key, in the Toolbox
i have 2 files in the Backup Folder

BENQ-OFW.BIN
BENQ-CFW.BIN

ok i loaded the BENQ-OFW.BIN (origin)
and the key ist is ok
i can see it.

what now....


The custom firmware ist the BENQ-CFW.BIN?????
It is also ok..Key ok
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: Kotana on May 08, 2008, 05:04:00 AM
What can i do now?????
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: speedspeed on May 08, 2008, 06:53:00 AM
E65: DVD Drive Error.... DVD Timeout, Wrong firmware, dvd is without f/w chip, etc. This can also be caused by the tray not being fully closed on boot.
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: podger on May 08, 2008, 07:04:00 AM
Make a back up of the orig.bin and then reflash the drive...... The firmware is most likely corrupt.... Reboot ff the usb/floppy and re-run fben, this should erase the flash and reflash bens-cfw.bin.... Watch the screen for any errors, wait til the job is finished....
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: podger on May 08, 2008, 07:15:00 AM
If you want to restore the original just boot the USB/floppy you used the first time, as long as you haven't formatted it of re-run iPrep, and run rben.bat... this is a 3rd file for flashing back the benq-ofw.bin....

pretty easy..
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: podger on May 08, 2008, 07:48:00 AM
You probably have a bad flash..... The whole power off/on thing is designed to induce this mode, but seeing as you are already there it gets a little more difficult to get it right....

Try leaving the drive on while you run rben....
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: Kotana on May 08, 2008, 12:23:00 PM
i reflashed the drive

writing finished!! DataSum: B1F0!!!!!

and the Drive still E65!!!!

What the F.......!!!!!
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: jimjom on May 08, 2008, 12:31:00 PM
ARE YOU ERASING BEFORE WRITING AGAIN?
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: techmob on May 08, 2008, 01:00:00 PM
QUOTE(Kotana @ May 8 2008, 08:26 PM) View Post

yes
erasing with fBen?!!!


have you plugged the sata cable back in on the xbox..?

have you another drive you can test?
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: podger on May 08, 2008, 02:34:00 PM
All those errors are coz the flash isn't erased properly......


When you did rben did the E65 go away?????
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: techmob on May 09, 2008, 01:58:00 AM
QUOTE(Kotana @ May 9 2008, 08:47 AM) View Post

No, the same E65 after rBen!!!!
I think the the same, the E65 is there because isn't erased...
How ca i erase the broken bin perfectly!?!?!?!Can you give me a short tutorial?
is Dosflash better for read and flash?
Is my DRIVE maybe brocken!?!?!?!
hope not!!!!!!!


i had the same problem http://forums.xbox-s...howtopic=649437

it was because the traces were not connected properly!

has your drive been dumped via switch in the past?
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: Kotana on May 09, 2008, 02:41:00 AM
no it has not been dumped...is the first time....
It is a new drive.
I think i have to flash with dosflas, to erase the broken FW.

How can i make a boot USB stick with dosflash?I now it whit iPrep....
Or how  to go ahead to do the flash?
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: techmob on May 09, 2008, 03:04:00 AM
QUOTE(Kotana @ May 9 2008, 10:17 AM) View Post

no it has not been dumped...is the first time....
It is a new drive.
I think i have to flash with dosflas, to erase the broken FW.

How can i make a boot USB stick with dosflash?I now it whit iPrep....
Or how  to go ahead to do the flash?



post 3 and 5 on the link i posted explained how

just download dosflash 1.3 and put it in the root of your sd card
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: Kotana on May 09, 2008, 07:51:00 AM
i have make the steps.....dosflash e .... 1 a0 1 4 d8 o
press Y and return, and power on the xbox...
from status 0x7F to status 0x80!!!!!!!!!!
i can get come in to erase the FW!!!!
how did you proceed?
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: NookularDeath on May 09, 2008, 08:00:00 AM
QUOTE(Kotana @ May 9 2008, 09:27 AM) View Post

i have make the steps.....dosflash e .... 1 a0 1 4 d8 o
press Y and return, and power on the xbox...
from status 0x7F to status 0x80!!!!!!!!!!
i can get come in to erase the FW!!!!
how did you proceed?



geezus!! find someone else to do your drive... after reading this thread I think it's safe to
say you aren't technically inclined enough to be doing this kind of thing..

Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: podger on May 09, 2008, 08:01:00 AM
what sata card are you using, is it fully compatible..
Title: After Flashing Benq , E65 And Drive Will Not Eject
Post by: podger on May 09, 2008, 06:13:00 PM
What is the chipset.... What you are doing will pnly definately work with a Via or nfroce 4 chipset.... If yours is not one of these then that is you problem...

Also Raid usually fucks up the entire process..