Post by: babe69 on November 15, 2007, 08:46:00 PM
using the soft flashing method
i have use the dosflash 1.3 to dump my orig.bin
use make iextrem firmware from BenQ iXtremev1.1MultiSpeed (non stealth) to have my xtreme.bin
go back to dosflash (manual method) erase command
writing command with xtreme.bin
done
checking my xbox360 with a original dvd and also backup dvd and i got put this game in a xbox360 console.
so i assume my xtreme.bin was not good
again
use Maximus 360 FW Toolbox v4.5 copy key from orig.bin ,open xtreme firmware paste key
close and open to check my key of xtreme.bin and it is the same.
go back to dosflash (manual method) erase command
writing command with xtreme.bin
go back to console
lower right red light appeared!!!!!!!! (IMG:style_emoticons/default/uhh.gif)
what happen??
im using vt6421r sata card
benq vad 6038
many thx
Post by: Ranger72 on February 02, 2020, 09:06:00 PM
Sounds like you may have gotten a bad firmware dump.
Post by: babe69 on February 02, 2020, 09:15:00 PM
give me a min
Post by: babe69 on February 02, 2020, 09:30:00 PM
QUOTE(Ranger72 @ Nov 15 2007, 11:06 PM) 
Flash your original bin file to your drive and see if originals load.
Sounds like you may have gotten a bad firmware dump.
with my orig.bin back in the console it work
the diff is the rom version
orig.bin 62430c
xtrem.bin 64930c
just a bad luck or corrupt xtrem.bin??
thanks for your help
Post by: babe69 on February 02, 2020, 10:07:00 PM
non-stealth firmware
erase command
write command
still lower right red light
with orig.bin all is ok
someone that have used non-stealth firmware from iXtreme_Firmware_BenQ_v1.1.MultiSpeed-XBOX360-iND
that has successfully flash a benq drive??
Post by: cypher21 on February 03, 2020, 02:11:00 AM
QUOTE(babe69 @ Nov 16 2007, 05:07 AM)
i retry to replace the key with maximus toolbox 4.5
non-stealth firmware
erase command
write command
still lower right red light
with orig.bin all is ok
someone that have used non-stealth firmware from iXtreme_Firmware_BenQ_v1.1.MultiSpeed-XBOX360-iND
that has successfully flash a benq drive??
toolbox has some issues with benq firmware
USE FIRMTOOL!!!!!
Post by: babe69 on February 03, 2020, 06:30:00 AM
QUOTE(cypher21 @ Nov 16 2007, 04:11 AM)
toolbox has some issues with benq firmware
USE FIRMTOOL!!!!!
thanks cypher21 for your help
as i state in my first post
i have use firmtool first ( dump orig.bin in firmware folder and run Make iXtreme firmware.cmd )
and i got " put this disk in a xbox ........ message" for original or backup
any ideas??
Post by: caster420 on February 03, 2020, 06:47:00 AM
QUOTE(babe69 @ Nov 16 2007, 08:30 AM)
i have use firmtool first ( dump orig.bin in firmware folder and run Make iXtreme firmware.cmd )
and i got " put this disk in a xbox ........ message" for original or backup
any ideas??
Did firmtool run and complete successfully? Firmtool automatically copies your version strings over, so your xtreme.bin should say it is a 62430, not 64930. It sounds to me like it didnt run or errored out, or it would have changed those strings at a minimum, even if it did for some reason find the wrong key.
Caster.
Post by: cypher21 on February 03, 2020, 07:26:00 AM
To be sure, create a new hacked firmware with 1.1
you can find the link in this threat: http://forums.xbox-scene.com/index.php?showtopic=629470
Post by: caster420 on February 03, 2020, 07:29:00 AM
QUOTE(cypher21 @ Nov 16 2007, 09:26 AM)
what also might be an issue, is that you use the older version of firmtool. Caster updated it to 1.1 because there were some firmwares that were dumped correctly but the hacked version wasn't created correctly.
That issue was only associated with spoofing BenQ firmware to report as a Hitachi or a Samsung, or spoofing Samsung firmware to report as a BenQ. Copying version strings of the same firmware type is not effected, or we would have had the issue from the beginning (a lot of people have v62430's when the hacked fw is v64930).
Still wouldnt hurt to update but i dont think thats the issue.
Caster.
Post by: cypher21 on February 03, 2020, 07:52:00 AM
QUOTE(caster420 @ Nov 16 2007, 02:29 PM)
That issue was only associated with spoofing BenQ firmware to report as a Hitachi or a Samsung, or spoofing Samsung firmware to report as a BenQ. Copying version strings of the same firmware type is not effected, or we would have had the issue from the beginning (a lot of people have v62430's when the hacked fw is v64930).
Still wouldnt hurt to update but i dont think thats the issue.
Caster.
Ah, in that case i didn;t read right, i thought there was one case which had a firmware you didn't see before and couldn't create the hacked version.
edit: found it, it was alinush' version of the benq
This post has been edited by cypher21: Yesterday, 03:54 PM
Post by: caster420 on February 03, 2020, 08:02:00 AM
QUOTE(cypher21 @ Nov 16 2007, 09:52 AM)
edit: found it, it was alinush' version of the benq
Yes, his firmware was messed up and is still the only one like that i have seen to date.
Caster.
Post by: babe69 on February 03, 2020, 03:11:00 PM
many many thanks to cypher21 and caster420 for there great help!
what it supposed to take 15 min. takes me abt 2 hours last night and all that for a software bug (IMG:style_emoticons/default/laugh.gif) (IMG:style_emoticons/default/laugh.gif)
great job guys
respect