Post by: SpIdErXeN on December 11, 2009, 05:39:00 PM
So, I'm thinking I have a 512mb Jasper, right? I'm not really sure since I'm an ultra noob to the NAND side of things, I was mostly into the drive firmware part of the scene. Anyways, I believe it's the power connectors on the power supply cable that tell you which version of the console you have, right?
My question is, is this console Jtag-able? I'd kill to get homebrew running on this thing, that's all I want for Christmas. (IMG:style_emoticons/default/laugh.gif)
Post by: danked on December 11, 2009, 05:56:00 PM
http://forums.xbox-scene.com/index.php?showtopic=698328
Post by: farmboynick on December 11, 2009, 05:59:00 PM
QUOTE(SpIdErXeN @ Dec 12 2009, 11:39 AM) 
Hey guys, I just bought an arcade unit today that has a mfg. date of 2009-04-17. It has a Dash Value of 2.0.7363.0 and Kernel Value of 2.0.1888.0. After setting up the unit, creating an avatar, setting the initial settings, I checked the "Memory" section, it said I had 322mb left of writable space.
So, I'm thinking I have a 512mb Jasper, right? I'm not really sure since I'm an ultra noob to the NAND side of things, I was mostly into the drive firmware part of the scene. Anyways, I believe it's the power connectors on the power supply cable that tell you which version of the console you have, right?
My question is, is this console Jtag-able? I'd kill to get homebrew running on this thing, that's all I want for Christmas. (IMG:style_emoticons/default/laugh.gif)
your console is exploitable, but at this time you can only run xell not freeboot or xbreboot, i think its only a matter of weeks before they will have a version of xbreboot to suit your console
Post by: TheCounter on December 11, 2009, 06:13:00 PM
But we have to wait till a new release of Freeboot/XBReboot since there is no support for 512MB Jasper yet. Ordered the resitors/diodes/wires yesterday and they hopefully will be here next week so i can dump my nand till a new freeboot/xbreboot is out. Dumping will be fun... 16hours for one dump lol (IMG:style_emoticons/default/biggrin.gif)
Post by: SpIdErXeN on December 11, 2009, 08:15:00 PM
Post by: SoloStyl on December 12, 2009, 02:32:00 AM
I have experience with this board, i bought 4 of them (IMG:style_emoticons/default/wink.gif)
it is exploitable and nand reads just fine on LPT port BUT takes forever, almost 9-10 hours for each read
im buying the USB port soon
I could not get my 1st CPU key because of the bad solder on "DB1F1" and "FT1u2" solder points
I RECOMMEND you use the bottom point, "FT1u2" or whatever it is called
it is right under the "DB1F1"
BUT...
"DB1F1" DOES NOT GO THROUGH THE Xbox360 MoBO, DO NOT TRY TO WELD WIRE THROUGH IT
Instead, add a bit of new solder to "DB1F1" or "FT1u2", and then weld your 1N4148 Diode
Some users said
"if you mess up on point "DB1F1", just scrape a little epoxy off the board and weld on the trace"
Again, I advise you NOT to do that, as that will cause a Short Circuit on the board,(it did on mine)
I dont beleive point "DB1F1" is meant to touch the thicker trace arround it, i measured and the thick trace is just "Ground Trace"
Good Luck
Post by: thwack on December 12, 2009, 04:35:00 AM
QUOTE(SpIdErXeN @ Dec 12 2009, 03:15 AM)
W00t! Hell yeah! Thanks guys for all the info, I really appreciate it! 16hour dump...ack, that's gonna be fun. TheCounter, man can you post, or pm me a link to where you bought all the equipment you needed to get the xell running on your Jasper? Also, just curious, and I will search the forums, may I ask...what specific components do you need to use in order to get xell running? Thanks guys.
1. PC printer cable or DB-25 male connector and wires.
2. 5X100ohm resistors (may need 68ohm, buy em as well they're cheap)
3. 3Xswitching diodes
4. Soldering iron, flux and solder.
5. Wire.
6. Remove R6T3 resistor on underside of 360
7. A lot of patience as you've got a 512mb NAND (IMG:style_emoticons/default/smile.gif)
Get the components from Radio Shack if your in the states, Maplins if in the UK.
This post has been edited by thwack: Dec 12 2009, 12:36 PM
Post by: SpIdErXeN on December 12, 2009, 01:28:00 PM
This post has been edited by SpIdErXeN: Dec 12 2009, 09:50 PM
Post by: SoloStyl on December 12, 2009, 03:17:00 PM
cant run FreeBoot, XBReboot, or any HomeBrew -YET. (IMG:style_emoticons/default/smile.gif)
I'm planning on using a new WD 7200RPM 1TB drive(if Possible) to install MAME,SNES emus etc.
finnaly wont need to switch arround my 2 M$ 60gig drives anymore. (IMG:style_emoticons/default/tongue.gif)
Post by: infidelity on December 12, 2009, 06:14:00 PM
I got xell to run, and i wrote down all of my fusesets (which is also how to obtain the cpu key)
My question is, what is the KV, and how/where do you obtain that in Xell?
Thank You (IMG:style_emoticons/default/smile.gif)
-infidelity
Post by: SoloStyl on December 12, 2009, 07:01:00 PM
you dont obtain it in Xell, KV is in the NAND
you use cpu key to extract/decrypt KV.bin from the NAND , but so far you dont need that because there is no homebrew for JASPER yet
just make sure to keep the NAND files and CPU key safe
Post by: infidelity on December 12, 2009, 07:21:00 PM
so is that why everytime i try to run the snes9x emu, or xmenu through xell, that it will not work on my 512mb Jasper?
Post by: SpIdErXeN on December 12, 2009, 10:46:00 PM
Post by: infidelity on December 13, 2009, 08:14:00 AM
well, as long as i know i didn't screw anything up, I can wait until xbr is released for the 512 jasper (IMG:style_emoticons/default/smile.gif)
thank you for the information
Post by: SpIdErXeN on December 13, 2009, 06:09:00 PM
Post by: SoloStyl on December 14, 2009, 08:04:00 AM
other than that running XELL is as easy as the Xenon,zephyr,opus,falcons
( maybe not Valhallas (IMG:style_emoticons/default/smile.gif) )