Print

[dpr99]

QUOTE(dpr99 @ Sep 27 2007, 02:34 PM)

i installed ndure 3.1 and when i use a component cable on a sd tv the picture is scrambled.  I hooked it up to a hdtv and the picture is fine and in the xboxdash all the hd settings are disabled.  so i think the high def or progressive settings are coded into nkpatcher.  is there anyway to change this?

i figured it out.  i created a NKP11_config.bin and commented out the force progressive setting.

[daviddrf]

QUOTE(kingroach @ Sep 26 2007, 05:46 AM)

launch E:\ndts\default.xbe.. now delete C:\shadowc\shadowc.img and copy a fresh shadowc from your coputer to xbox's C:\shadowc\ folder.. ( shadowc.img is created by the installer in C folder).. now shadowc should be writable.. copy a fresh C drive files from slayers disk to shadowc..

Hello, I´ve the same problem than snakesnoke but I still didn´t find the solution.
I want to start with Unleash X when I power on the Xbox with the little button and to start the Ms Dash when I start ejecting the tray. But after installing Ndure 3.1 I get Unleash X when I start ejecting the tray.
When kingroach says: "copy a fresh C drive files from slayers disk to shadowc.." does he mean to copy a clean C drive from Slayers to C:\shadowc (folder in C:\) in the Xbox Hard Drive???.
I installed Ndure 3.1 with the 2nd (of 5) Option at Xboxhdm. When I used the installer I tried this two configurations:
1. CORE FILES; SOFTMOD & NKPATCHER OPTIONS: Install Ndure Basic and Use Nkpatcher .06; KERNEL SELECTION : 4817; ADD UDDAE; CREATE XBOXHDM Installer.
2 . CORE FILES; SOFTMOD & NKPATCHER OPTIONS: Install Ndure Basic, Use Nkpatcher .06, Boot XBL dash with eject and Boot XBL dash with UDDAE; KERNEL SELECTION : 4817; ADD UDDAE; CREATE XBOXHDM Installer.
With these 2 configurations it didn´t worked for me. I have a 1.1 Xbox with a 80 GB Seagate Hard Drive. I also read the Ndure Installer For Pc 3.1 (the pdf too) and Xboxhdm For Dummies. ¿Could anyone help me please?. Sorry for my very big quote and my bad english reading/writing. Bye!

[xman954]

QUOTE

When kingroach says: "copy a fresh C drive files from slayers disk to shadowc.." does he mean to copy a clean C drive from Slayers to C:\shadowc (folder in C:\) in the Xbox Hard Drive???.

No thats only to fix a non writable C:\ (shadowC only)

QUOTE

Boot XBL dash with eject and Boot XBL dash with UDDAE

you can only select one or the other.
also don't select basic

re-run the installer with a new set of MS files and use them
it's a lot faster to just use the NDTS and FTP the proper files to the real C:\

This post has been edited by xman954: Sep 30 2007, 07:31 PM

[dpr99]

what is the difference between using the xboxhdm script or just putting the softmod files in the correct c and e folders of xboxhdm before creating the iso?

[kingroach]

if you copy the softmod files in C and E folders of xboxhdm then you need to use rebuild harddrive option to create the hrddrive and then xboxhdm will copy teh files to appropriate partition.

[whenever]

hello kingroach, could you please post your NKPatcher .inc files for Ndure retail setup? That will help us to change some settings but not mess up other settings in case we want to recompile NKPatcher.

[dpr99]

QUOTE(whenever @ Oct 2 2007, 10:57 PM)

hello kingroach, could you please post your NKPatcher .inc files for Ndure retail setup? That will help us to change some settings but not mess up other settings in case we want to recompile NKPatcher.

i was going to ask for this too

[daviddrf]

QUOTE(xman954 @ Sep 30 2007, 08:28 PM)

No thats only to fix a non writable C:\ (shadowC only)

you can only select one or the other.
also don't select basic

re-run the installer with a new set of MS files and use them
it's a lot faster to just use the NDTS and FTP the proper files to the real C:\

Thanks dpr99. The problem is now solved with your information. The reason was my low english level. I´m sorry and thank you!.

[kingroach]

QUOTE(whenever @ Oct 3 2007, 04:57 AM)

hello kingroach, could you please post your NKPatcher .inc files for Ndure retail setup? That will help us to change some settings but not mess up other settings in case we want to recompile NKPatcher.

I uploaded my working nkpatcher folder here with the config file :

http://www.esnips.com/web/kingroach/

file name is NKPatcher11_U04-kingroach.rar

[Keypel]

I have a large Harddrive (500gb) I did not see a Nkpatcher .67 Option. All I saw was

CODE

Softmod & Nkpatcher Options
    Install Ndure Basic
    Use Nkpatcher .06
    Boot XBL dash with eject.
    Boot XBL dash with UDDAE
    Enable clock check
    Use Nkpatcher RGB

How do I get the xbox to reconize my 362.668.91MB G Drive I formated with xboxpartioner?

[kingroach]

It uses nkpatcher .67 by default..

[Keypel]

Thanks for clearing that up kingroach.

[hancsicsak]

Hello All

I have been playing with the install for a few days now and it is a pretty impressive set of tools.  I have been able to work my way through softmodding my XBox and getting the MSDash to work through Unleash, but I have not been able to get it to work through the eject button.  I keep getting an Error 21.

After looking at the NKP11 config file for the tray open dash, what dashboard name and location is used when using the retail settings?

Thanx

[xman954]

QUOTE

what dashboard name and location is used when using the retail settings?

when using
%define KINGROACH_VERSION

without E:\NKP11\boot1.bin
PB_OPEN_PATH   '\Device\Harddisk0\Partition2\xb0xdash.xbe'

with any file named boot1.bin in the E:\NKP11\ dir
OPEN_PATH        '\Device\Harddisk0\Partition2\xodash\x2onlinedash.xbe'

both are on the real C:\ not the shadowC
xb0xdash.xbe is a orignal xboxdash.xbe renamed
x2onlinedash.xbe is a modified xonlinedash.xbe

This post has been edited by xman954: Oct 10 2007, 04:22 PM

[hancsicsak]

Thanx xman

I will have to look and make sure I have a proper running MSdash from the real C.  I have only been testing from the shadowC.