xboxscene.org forums

Author Topic: Matrix Prob  (Read 119 times)

Brando

  • Archived User
  • Newbie
  • *
  • Posts: 3
Matrix Prob
« on: October 19, 2004, 05:43:00 AM »
I have had my mod chip (pretty much since the UK launch) a while now and it has now started to mis-behave. On mode 1 I have a flashing green light and mode 3 I have a solid green light, but the XBOX continues to boot off it's original bios :(. Can you guys help.....

 :uhh:
Logged

Mike~B~

  • Archived User
  • Newbie
  • *
  • Posts: 1
Matrix Prob
« Reply #1 on: October 19, 2004, 12:52:00 PM »
mine did this i had to reseat it and apply another force to keep its connection
Logged

valius

  • Archived User
  • Full Member
  • *
  • Posts: 117
Matrix Prob
« Reply #2 on: October 19, 2004, 08:43:00 PM »
Sounds like the DO point is not making proper contact with the board.

The single springloaded pin @ the top of the chip connects to the Do point, try cleaning the Do point & then re-fit the chip.

The led's on your chip will light up as normal as long as the lpc pins are making proper contact with the board & the Do pin dosen't
Logged

Exzir

  • Archived User
  • Full Member
  • *
  • Posts: 248
Matrix Prob
« Reply #3 on: October 20, 2004, 03:59:00 AM »
The light is only that the d0 is alligned and not anyother pins other than pin 1 (ground and the power pin 3.3 volts I think.  If these three pins are aligned then it will be green.  This still leaves 7 pins that needs connecting and there aren't any lights for them.  Just try loosening the screw and tightening the screw with just a little at a time till you know it is booting off the matrix chip.

Logged

Brando

  • Archived User
  • Newbie
  • *
  • Posts: 3
Matrix Prob
« Reply #4 on: October 20, 2004, 07:54:00 AM »

Thanks for your help so far guys! But which way round is it??

Does it flash green when d0 is align or the other 7 pins??


I will try some more tonight, I have cleaned it and I have a small pit on one of the 7 pins, may try and resolder it. :popcorn:
Logged

valius

  • Archived User
  • Full Member
  • *
  • Posts: 117
Matrix Prob
« Reply #5 on: October 20, 2004, 11:19:00 AM »
It will flash green with only the 7 lpc pins connected, I think I seen something about having to recover the L frame in order to get a matrix to work in anything over a 1.2

you might want to look into that first before retry..

The easiest way would be to get a compatable mod for you new box & keep the matrix in the old one.

Have you considdered flashing the Tsop? it's not as hard as you might think...

Good luck, Valius
Logged

Exzir

  • Archived User
  • Full Member
  • *
  • Posts: 248
Matrix Prob
« Reply #6 on: October 20, 2004, 07:50:00 PM »
It does not matter of all of the lpc are connected if it flashes green.  I have soldered the d0 for a 1.2 matrix install (it falshed green all the time even when it was not working.) I did nothing for the pin 7.  I only removed pin 7 for a 1.6 mother board.  The chip for the 1.2 I always knew it was aligned for the d0 since it was soldered but for the other lpc pogos I had to clean them some times.  Carbin or something stopped them from makeing a good connection.
Logged