Topic: Chipped Xbox Suddenly Stopped Working! (Read 233 times)

Conehead · « **on:** February 17, 2005, 10:22:00 AM »

I chipped my xbox 5 months ago and it worked perfectly ever since, Then i turned it on the other day and it wouldn't start at all. I've reflashed with the latest version of Evox but it won't start, I can boot with Linux or Cromwell but i get the message "unable to find first sector" I've flashed and reflased the chip a few times and even tried a different Hard Drive!! any help will be much appreciated

Easybuy2000 · « **Reply #1 on:** February 17, 2005, 11:58:00 AM »

Which chip do you have in your Xbox the X-Chip or X-Lite.

Since you state that chip is installed for 5 months I assume its the X-Chip.

How about if you remove the X-Chip from the Xbox does the Xbox boot normally.

This post has been edited by Easybuy2000: Feb 17 2005, 08:00 PM

Conehead · « **Reply #2 on:** February 17, 2005, 03:38:00 PM »

Yeah it's the Xchip i've emoved it but it won't boot normally i think the dashboard has changed too much to boot as a normal Xbox! any ideas??

christineyoung · « **Reply #3 on:** February 17, 2005, 09:40:00 PM »

Can you load harddriev via cd if so, try ing using slayers and restore reatil drive and see if it boots.

ALso, may need to look at IDE cable on harddrive.

Are you getting any flashing when trying without modhcip on power button? If so what colors, also was this a solder install or solderless.

Meithos · « **Reply #4 on:** February 20, 2005, 05:12:00 PM »

Um, can't find first sector? Doesn't that usually mean it's a hard drive error, ie. your hardrive has a bad sector? Would make sense to me, I'd try putting in another drive and put an msdash/evox dash, then try again..

bobpulsan · « **Reply #5 on:** March 08, 2005, 08:59:00 AM »

I am having the same problem as conehead.

I have swapped the ide cable but nothing changes. I have swapped my 120gb harddrive back to the original xbox harddrive, and still the abox will not boot.

When I load the complex debug bios into my x-chip I can boot from an evolution x boot disc butI am unable to ftp into the box.

I am stumped at this point.

LenteSubigo · « **Reply #6 on:** March 08, 2005, 02:44:00 PM »

QUOTE(bobpulsan @ Mar 8 2005, 08:59 AM)

I am having the same problem as conehead.

I have swapped the ide cable but nothing changes. I have swapped my 120gb harddrive back to the original xbox harddrive, and still the abox will not boot.

When I load the complex debug bios into my x-chip I can boot from an evolution x boot disc butI am unable to ftp into the box.

I am stumped at this point.

Ok, whe you try to boot with the original bios(chip removed, or disabled) what does it boot to? Do you get the multilanguage error with a 2 digit error code in the top left corner? If so what is the error code? Or, are you just getting black screen with the eject light flashing diferent colors? If so what colors?

bobpulsan · « **Reply #7 on:** March 19, 2005, 11:02:00 AM »

Sorry for taking so long to get back to this.

When I uninstall the mod chip and replace the original hd all I get is a blank screen with a red flashing eject button.

christineyoung · « **Reply #8 on:** March 20, 2005, 09:12:00 PM »

What version xbox is it?

also the FLASHING RED means: Dead, broken or empty eeprom. Possible corrupted as well.

If you made a backup of your eeprom with the XChip, you can connect Xchip to Xbox and press and hold the button on the programmer for 5 seconds while powering up, this will rewrite the stored eeprom back to the xbox.

If not i beleive you can embed and write a new flash with added eeprom to XChip using the utility included with Evox 1.3 using yoiur PC and USB cable and boot up with same procedure listed above after programmed.

bobpulsan · « **Reply #9 on:** March 22, 2005, 08:29:00 AM »

Its a v1.0 box.

Unfortunately I lost my eeprom back up. If I was to purchase a new eeprom woud this solve my problem. I dont believe that I locked my hd but if I did, is it now completly useless?

Are a new eeprom and new hd call for?

christineyoung · « **Reply #10 on:** March 22, 2005, 05:46:00 PM »

I would copy or use someones banned eeprom( most like get one for free ) just to see if you get video etc, if harddrive locked you maybe screwed at accessing it...but i'm sure you could extract keys off eeporm chip still on system if it has not been rewritten

bobpulsan · « **Reply #11 on:** March 28, 2005, 05:08:00 AM »

I think I have to accept the fact that my Xbox is dead!

I got a friends eeprom and his unlocked retail drive with evolution x on it. Put both into my box and all I get is an error 21 message. Im giving up at this stage.

Anti · « **Reply #12 on:** April 14, 2005, 12:17:00 PM »

sounds like it's toast to me. just go buy another they don't cost very much now adays

This post has been edited by Anti: Apr 14 2005, 07:19 PM

Author Topic: Chipped Xbox Suddenly Stopped Working! (Read 233 times)