Topic: Tutorial - Complete Walkthrough (Read 364 times)

Mad_Gouki · « **on:** July 13, 2003, 11:26:00 AM »

update: both are the user friendly version now

this is my home site, it iwll be updated with new tutorials ect.
new url: http://freexevoxtut.freeservers.com/

http://www.sbeyer.ne...ouki/index.html

http://quikboard.com/xboxxx/index.html

zanderch · « **Reply #1 on:** July 13, 2003, 05:13:00 PM »

This is a very good tutorital, but what do I do if the Ip says 0.0.0.0 in EVOX?

Mad_Gouki · « **Reply #2 on:** July 13, 2003, 07:16:00 PM »

i forgot to add this to the tut
you need to set use static ip to yes and then scroll down to the bottom and pick save and exit
then restart the xbox and load the game over

absolutejerk · « **Reply #3 on:** July 13, 2003, 11:05:00 PM »

Nice work bro!

Your instructions worked for me on a used Xbox I got for 50 bucks

I had my games backed up on my other modded xbox's HD. I used Xtoolbox to move the games from Xbox to Xbox. I had to pay attention to the final steps of your instructions to get the games working on the unmodded Xbox.

absolutejerk · « **Reply #4 on:** July 14, 2003, 06:01:00 AM »

I had a fonts folder. I did not remane bert and earnie, I just stuck em in that fonts folder.

Can you use the F drive after doing the 007 trick? The 5 Gigs on E is not much room.

zanderch · « **Reply #5 on:** July 14, 2003, 06:21:00 AM »

Thanks. Now it says my IP address but I still can't connect using Flash FXP. Can you tell me how?

XBox_Master_King4469 · « **Reply #6 on:** July 14, 2003, 09:31:00 AM »

i have a simular prob

i did everything right like the tutorial said and the FTP worked at first... now im getting this error that says "there is a IP address conflict with another system on the network" error. also when it does work its not getting any info from the xbox

it worked when i 1st installed Evox what should i do?

Mad_Gouki · « **Reply #7 on:** July 14, 2003, 10:50:00 AM »

i dunno man...
and no you do NOT rename bert and ernie!!!! does it say to rename bert and ernie to xbox and xbox book? no... then you dont do it...
you rename xbox.xtf and xbox book.xtf to XFT files...

trust me on this... and after you do this there is a way to edit the xboxdashboard in hex and change xtf to xft so it will actually boot from evox!

and about the ftp's
contact me over icq
35454223
aim
MadGouki
y!
Mad_Gouki
or msn
[email protected]

and talk to me, i will try and help yo uwith the ftping, ive had people say its hard to do with a hub...

Mad_Gouki · « **Reply #8 on:** July 14, 2003, 03:02:00 PM »

im going to write a "how to run the xbox dash through evox" for the tutorial... ill be adding that within the next few days

XBox_Master_King4469 · « **Reply #9 on:** July 14, 2003, 03:06:00 PM »

thank god but i only have 007 till 2marrow (rent) and i allready made it go back 2 the orginals

Mad_Gouki · « **Reply #10 on:** July 14, 2003, 03:18:00 PM »

master king, you may want to im or pm me and i can help you with the dash....
if you can only keep it till tomorrow you will want to do this tonight...

and really its probably smart to buy 007 in case something goes wrong...

Mad_Gouki · « **Reply #11 on:** July 14, 2003, 04:58:00 PM »

QUOTE

Connecting the XBOX to a network that uses an internet router/residential gateway.
I recommend you read the entire tutorial once before you get started. This FAQ may not be 100% consistent for EVERY router out there, but it should help you FFIO.

A router is a device which allows multiple computers to connect to the internet. Its main purpose is to share an internet connection. Most routers are setup to do assign the devices on your network an IP address. The protocol that handles IP addressing is called DHCP. When your computer gets one of these addresses, its called a dynamic IP This is OK for your computers, but not so good for the XBOX. If you arent familiar with your router and DHCP, then you will have a hard time figuring out which IP address the XBOX takes (that makes it impossible to FTP to!) With dynamic address, there is also a chance it will change. So what works one day, may not work the next. The solution it so set the XBOX up with a Static IP address.

1. Determine the IP range of your network. This will help you figure out what address to give the XBOX.

Win9X/ME
Go to Start > Run and enter command. Click OK.
From the command prompt, enter ipconfig /all (no quotes) and hit Enter.

Win2k/XP
Go to Start > Run and enter CMD. Click OK.
From the command prompt, enter ipconfig (no quotes).

Take note of your Ethernet adapters IP address, subnet mask, and default gateway.
The first three sections (octets) of your IP Address are important. Notice how they are the same for the Default Gateway, probably either 192.168.0.X or 192.168.1.X. You are going to give your XBOX an address in the same range. Your subnet mask isnt too important for this stuff. If your IP address is something like 169.254.X.X, you may not have a router. FFIO.

2. Figure out what IP is available to assign your XBOX. All the computers that connect to your network should be turned on for this step.

Pick an address to assign the XBOX. When I say pick an address, I really mean pick any number between 2-254. I started at 2 because your default gateway was probably 192.168.X.1.

My computers IP address was 192.168.10.105, and my gateway was 192.168.10.1, so I picked 192.168.10.20 for the XBOX. I didnt pick 106 or 104 because DHCP may have assigned one of those addresses to one of my other computers.

Still at the command prompt, enter ping and the IP address you picked for the XBOX (ex: ping 192.168.10.20). You should get 4 request time outs. If you get replies, then the address you picked to use for the XBOX is already is in use on your network. Assigning that address to the XBOX will cause an IP conflict. Pick another number and ping again. Once your ping requests time out, you found an available address to assign the Xbox.

3. Now you need to Edit your evox.ini file.
You need to enable Static IP then enter the IP information you found previously.
IP 192.168.10.20
Net Mask 255.255.255.0
Gateway 192.168.10.1

HSDEMONZ · « **Reply #12 on:** July 14, 2003, 09:57:00 PM »

Temp Pin

Mad_Gouki · « **Reply #13 on:** July 14, 2003, 11:03:00 PM »

Hath · « **Reply #14 on:** July 15, 2003, 08:32:00 AM »

is it possible to upgrade the hdd through this exploit. ?

Author Topic: Tutorial - Complete Walkthrough (Read 364 times)