Topic: Homebrew Layout For The V1.2! Working And Tested! (Read 753 times)

D-BlooD · « **Reply #15 on:** May 05, 2003, 06:02:00 PM »

Hi _Access

All I can say is that it works with my homebrew at least

Some more information on chip used and homebrew layout would be gr8t

Kinda hard helping you solve your problem if we dont know how and what you have connected

Best Regards
D-BlooD
http://www.xunlock.com

_Access · « **Reply #16 on:** May 05, 2003, 04:37:00 PM »

sorry for doauble post, but correct me if i'm wrong shouldn't we be using homebrew made up of 256kbyte as it's a 2mb tsop- 4x256k.

D-BlooD · « **Reply #17 on:** May 05, 2003, 05:56:00 PM »

I guess you must be doing something wrong, becouse I have double checked it and it works gr8t on two different boards now.

Best Regards
D-BlooD
http://www.xunlock.com

jawuelln · « **Reply #18 on:** May 05, 2003, 09:37:00 PM »

Can you mod a version 1.1 with an enigmah chip, fried my onboard bios with matrix and can't boot.

D-BlooD · « **Reply #19 on:** May 06, 2003, 12:02:00 AM »

This at least is my experiance. For a unknown reason when fitting the matrix some people mangage to erase the tsop somehow

Now you could try using a homebrew to TSOP flash your box, and then remove it. Prob the easyest if you dont have a test clip tool of some kind or the tools to remove your TSOP and get it reprogrammed.

Best Regards
D-BlooD
http://www.xunlock.com

_Access · « **Reply #20 on:** May 06, 2003, 01:25:00 AM »

_Access · « **Reply #21 on:** May 06, 2003, 06:04:00 AM »

well i'm back after taking me time installing...still flashing, so after taking it out and putting it into unflashed v1.1 xbox it booted fine, just have to see and wait see any 1 else has any probs with the v1.2 layout.

Lobotomy · « **Reply #22 on:** May 06, 2003, 08:07:00 AM »

and yes, i've inserted the line into my evox.ini

D-BlooD · « **Reply #23 on:** May 06, 2003, 08:49:00 AM »

Btw: gr8t work on gettnig your homebrew up and running, now at least we are 2

heh

Best Regards
D-BlooD
http://www.xunlock.com

GTO_2001 · « **Reply #24 on:** May 06, 2003, 10:06:00 AM »

Hi,
@D-Blood :
great work !!!

But i am too stupid to find pin A19 at my Eprom.
Which other name it has ? Or better : Which Pin it is (1......32)

BIG THX

GTO_2001

D-BlooD · « **Reply #25 on:** May 06, 2003, 10:59:00 AM »

www.goggle.com usualy solves 99.9% of problems like this, try searching for the datasheet of the chip you are using.

For me to tell you what legs 1-32 on your flash/eprom is almost impossible.

From now on if anyone have any questions about theyr homebrew not working with this layout and or not beeing able to TSOP flash PLEASE post the name/type of the homebrew chip and connections shorted to enable TSOP flashnig if the question is regarding TSOP flash. Posts without this information will at least not be answerd by me if the information is missing.

Best Regards
D-BlooD
http://www.xunlock.com

GTO_2001 · « **Reply #26 on:** May 06, 2003, 11:10:00 AM »

Hi,
you are right, i am using a AMD 29F040.

So you mean i can try it to solder without this Point ?

Thx for your answer ....

cu
GTO_2001

_Access · « **Reply #27 on:** May 06, 2003, 12:38:00 PM »

arrgghh....i can't see whats wrong ive changed me eprom for 2mb, flashed it using executer2 bios still no joy..but works wonders in v1.1, theres only 6 points which have changed on the v1.2 board..ive never had this problem with v1.0, v1.1..it's just the v1.2 which is givin me a headache :/

GTO_2001 · « **Reply #28 on:** May 06, 2003, 01:50:00 PM »

Your'e the gratest, man !!!

I go to bed now, dream of my new fresh modded LE.

cu
GTO_2001

_Access · « **Reply #29 on:** May 06, 2003, 03:10:00 PM »

...ok ive used a diffrent eprom once again 27c801 8mbit..but this time the vcc point i sent that vss and it boots..will post more tomorrow

Author Topic: Homebrew Layout For The V1.2! Working And Tested! (Read 753 times)