Print

[Slirpy]

Homebrew would be better than using 007 hack cause I am now fixing a dead box that was "hacked" via 007 exploit. Now I have to waste my time on researching the 3 or 4 different tutorials/posts that tell you how to enable TSOP flashing cause I have never done it yet. Where is your backup with flashing the TSOP with no modchip connected? Thanks to D-Bloods post here I may be able to fix this 1.3 box
Still not clear on all the points I need to link and connect to switches. Would it be ok to just use wires and then cut the wire for the switch part? I will try that. I would like to double check what I "think" I have to do. I have the chip soldered normally and it boots, but now to flash the TSOP I need to connect pin 31 to the point labelled E, and then 24 goes to the point labelled G (or does it just need to still be connected to pins 16 and 22?). Now when the box boots to evox I just cut the wires and go flash the chip? Thanks for any replies.

[D-BlooD]

(IMG:http://www.xunlock.com/Pics/done.JPG)

Hope the picture speaks for itself.

And add the following line to evox.ini if you want to be able to TSOP flash the ST M29F002BT70N1 from the Evolution-X flash menu.

Flash = 0x20b0,"ST - D-BlooD R0X y0 B0X",0x40000

Have phun and post questions if you have any

[pulz]

Great work as always d-blood, keep it up  

[XanTium]

Thx for posting this info :-)

[cjack]

WHOW Super!!! Thank's a lot, your help with 1.2 homebrew is very appreciated!!!

[TykSak]

Damn! Now I have to get a Ver1.2

Thanks and good job (IMG:http://www.modzone.dk/forums/images/icons/icon14.gif)

[menase]

I assume this will work for enigmah and other 29 wire style modchips for the 1.0... but how to tell which wires go where...
also would this work for the v1.1?

[Lobotomy]

Nice!

I've been trying to mod a green v.1.2

I looked at your points, but... wheres the A9 point? (point 26 on homebrew diagrams)

[XanTium]

QUOTE (menase @ May 5 2003, 06:38 PM)

I assume this will work for enigmah and other 29 wire style modchips for the 1.0... but how to tell which wires go where... also would this work for the v1.1?

 it will 'not' work with enigmah , because the enigmah modchip has a bios only working on 3944/4043 v1.0 bioses.

v1.1 has same points as v1.0 as far as I know (never tried to mod a v1.1 with a gen1 mod though) - but once again , you need a compatible bios with your xbox version.

[qortizone]

Can someone please explain where A9 is ? And what is the one point that says RP ? (or is that A9 ?) Thanks

[D-BlooD]

Oh sorry about that guyes.. after fixing my first picture that was totaly blurry when I was done with it I forgot tp add A9 on the new one.. If you look at the picture now it should be fixed

RP = Reset/Block temporary Unprotect

Best Regards
D-BlooD
http://www.xunlock.com

[qortizone]

Sorry, I still don't see A9. Please try upload again.

[D-BlooD]

Try Refresh / F5 key Its there.. The picture is linked and changed when I uploaded the new one  

Best Regards
D-BlooD
http://www.xunlock.com

[Lobotomy]

Thanx man!

gonna try it tomorrow after work.

great job!

I O U a beer!  

[_Access]

here we go, ive wired a homebrew chip using evox v1.1 bios to the points shown above but all i get is red n green flashing light, the homebrew i use works ok in v1.1 models, but if i remove the homebrew the xbox boots fine, ive gone over the points and everything is fine.


greets to dblood for posting 1st homebrew diagram for v1.2