Topic: Flashing Help (Read 582 times)

run088 · « **Reply #15 on:** July 26, 2009, 11:58:00 PM »

I have never had that problem before so I really cant say but a cheap 13 dollar modchip will bypass the problem. The 3 wire trick wont work because you successfully flashed the whole tsop.

Will it load a disk? Can you hear it?

KILLxQUICK · « **Reply #16 on:** July 27, 2009, 12:03:00 AM »

yes it loads i put a game in and can hear it loading and i can hear music through speakers.

ill have to find some disks that will work with my xbox and figure out a way to reflash.

run088 · « **Reply #17 on:** July 27, 2009, 12:05:00 AM »

Then if you get slayers I can walk you threw the menu and we can try to flash a different bios.

Or a linux disk might be able to work it might hijack the bios since it is based off pbl.

Might be able to get away with flash bios since it is based off cromwell.

I think it can be fixed without a modchip but it will be tricky.

You might also want to try to use a different av method and see if it produces a more usable signal it would not hurt to try.

KILLxQUICK · « **Reply #18 on:** July 27, 2009, 12:10:00 AM »

ok thanks for all your help man, i guess thats all for now until i get some disks.

i have a disk that works but its full so ill try and find some more of the same kind.

KILLxQUICK · « **Reply #19 on:** July 28, 2009, 06:32:00 PM »

ok so it boots up unleashx but no video, i think i can run evox and fix the problem though.

KILLxQUICK · « **Reply #20 on:** February 17, 2010, 09:38:00 PM »

I know this thread is old but, could i possibly fix this problem by getting the xbox to boot into PBL?

KILLxQUICK · « **Reply #21 on:** February 17, 2010, 10:05:00 PM »

yes i have ftp access.

KILLxQUICK · « **Reply #22 on:** February 17, 2010, 10:17:00 PM »

umm would you know how i would go about doing this? and i think i had unleash as my primary dash so i will need to change that to evox.

KILLxQUICK · « **Reply #23 on:** February 17, 2010, 10:48:00 PM »

ok and its a conexant tsop

KILLxQUICK · « **Reply #24 on:** February 17, 2010, 11:13:00 PM »

oops my bad i havent messed with this stuff in a while, its a Hyundai tsop

steveo1978 · « **Reply #25 on:** February 17, 2010, 11:41:00 PM »

ok I will have the edited evox.ini file post up tomorrow. You will have to go on xbins and get the bios and if you dont already have evox get that to. I would suggest getting Ind-Bios 5003 that way you know for sure you are not grabbing a bios for a 1.6 xbox

KILLxQUICK · « **Reply #26 on:** February 17, 2010, 11:44:00 PM »

ok thanks dude.

murauder · « **Reply #27 on:** February 17, 2010, 11:51:00 PM »

if you can ftp then just ftp in and point the x2 config to your evox dash edit the ini to add THIS. delete everything in your menu and just have it set up to have this

Item "Flash BIOS",ID_Flash_Bios

if that doesnt work then change it to

Item "Flash BIOS",@1

put your bios in a bios folder where your dash is located

then you will have to click A 3 times i believe it is (its been a while since i used evox)
wait.....
and you should have successfully flashed your TSOP with the right (x2 5035 vOLD i assume) BIOS

edit: too late! damn me and my slow typing!

KILLxQUICK · « **Reply #28 on:** February 18, 2010, 08:00:00 AM »

ok, that sounds like it just might work. Ill give it a shot when i get home later.

*edit: well as of now it wont turn on so ill have to figure that out later too.

KILLxQUICK · « **Reply #29 on:** February 18, 2010, 05:52:00 PM »

ok another stupid question, where do i put the evox stuff cause there is a spot in C and E? (im assuming C)

what needs to be replaced because in ftp my C drive consists of: fonts, SID, Skins, Config.xml, evox.ini, evoxdash.xbe, items.xml, and xboxdash.xbe.
(knowing that evox.ini and evoxdash.xbe need to be replaced)

Author Topic: Flashing Help (Read 582 times)