Topic: 1.1 Sharp Tsop Not Writable? (Read 76 times)

xboxexpert · « **on:** July 27, 2006, 07:12:00 AM »

For my sharp I soldered one wire to each solder point of the TSOP points (4 points in total)

Ran the wires up the board and soldered two switch's so when the xbox was on I can flick the switch's and bridge the points together. Then I flashed it. Worked 100% for me, I hope you have the same results.

vb_master · « **Reply #1 on:** July 27, 2006, 07:45:00 AM »

QUOTE(xboxexpert @ Jul 27 2006, 09:19 AM)

For my sharp I soldered one wire to each solder point of the TSOP points (4 points in total)

Ran the wires up the board and soldered two switch's so when the xbox was on I can flick the switch's and bridge the points together. Then I flashed it. Worked 100% for me, I hope you have the same results.

I'm not going to use a switch. Can someone provide a good image of what it is supposed to look like? (I want to use 2 wires, not bridging those spaces).

caster420 · « **Reply #2 on:** July 27, 2006, 09:48:00 AM »

Use these photos for the sharp. Slushies tut is confusing and i dont really like it.

Caster.

vb_master · « **Reply #3 on:** July 27, 2006, 10:00:00 AM »

QUOTE(caster420 @ Jul 27 2006, 11:55 AM)

Use these photos for the sharp. Slushies tut is confusing and i dont really like it.

Caster.

Oh, so that's why it said protected. I didn't know there was an enable point on the front of the mobo!

vb_master · « **Reply #4 on:** July 27, 2006, 12:14:00 PM »

Ok guys I soldered the 3 wires, and whenever I turn on my Xbox, it doesn't display any video. If I try to eject the DVD, it shuts off and reboots. Suggestions?

caster420 · « **Reply #5 on:** July 27, 2006, 12:21:00 PM »

I have never flashed a sharp before, but in that post is says to join a and b after boot when you're ready to flash. I am not sure if this will effect it or not.

Caster.

vb_master · « **Reply #6 on:** July 27, 2006, 12:30:00 PM »

QUOTE(caster420 @ Jul 27 2006, 02:28 PM)

I have never flashed a sharp before, but in that post is says to join a and b after boot when you're ready to flash. I am not sure if this will effect it or not.

Caster.

Yeah, I noticed that too. I didn't think it would matter. I will try using longer wires and twist them.

vb_master · « **Reply #7 on:** July 27, 2006, 12:56:00 PM »

Ok I did that, it boots! I went into EvoX -> Systm Utils. (twisted wires) -> flash BIOS, selected my BIOS, it said press Y to flash. Did that. It's been saying erasing for like 3 minutes.

Ok I turned it off and untwisted. It still boots. Any ideas?

caster420 · « **Reply #8 on:** July 27, 2006, 01:02:00 PM »

Try using raincoat. I've never used evox to flash, so i cant help you there.

Caster.

vb_master · « **Reply #9 on:** July 27, 2006, 01:05:00 PM »

QUOTE(caster420 @ Jul 27 2006, 03:09 PM)

Try using raincoat. I've never used evox to flash, so i cant help you there.

Caster.

Trying to use Eurasia and a verified EvoxM7_blue_1mg BIOS.

Eurasia just blackscreened, now trying something else.

quiksilver_kid · « **Reply #10 on:** July 27, 2006, 02:04:00 PM »

Im pretty sure you need to use raincoat to flash sharps, evox and the like will not work.

xboxexpert · « **Reply #11 on:** July 27, 2006, 02:50:00 PM »

Yawn....switch.....yawn

Shadow3223 · « **Reply #12 on:** July 27, 2006, 03:35:00 PM »

U should have used raincoat from the beggining and you would already have a flashed TSOP...but oh well waste $12.99 if u want.

Author Topic: 1.1 Sharp Tsop Not Writable? (Read 76 times)