Topic: Winbond (Read 84 times)

zipo1200 · « **on:** January 08, 2005, 11:05:00 AM »

Okey this is a little odd. i have soldierd the points correctly and actually triple checked the points to make sure that a proper connection is in contact. 1 top one bottom (v1.2 xbox) and tried to flash the winbond with evoX or to at least get the proper flash type. since i am not entirely sure of the *.bin size. so i was wondering if its evoX cousing this failure. i have correctly placed the winbond flash types in my evoX.ini of my splintercell exploit and it will give me that error "Flash not writable"

now i looked again at the soldiering screen shots and they are corectly intaked. i even scratched the surface just a little bit on the bottum soldier poijnt, just to make sure a proper connection was there.

so how else can i go off with this. i have modded many xbox's tsop's but mostly of any of them i have done. was "st's and hynix's" no problem through evoX

should i use, excuse my spelling if it isnt correct ( and since raincoat doesnt seem to work and hang at the loading screen) "Eurosia"

if anyone that has done a winbond have any advice or can say again the correct soldier points (just to make 100% sure) if the tutorials are not correct in any case for his particular winbond, it would be greatly appreciated!!!

i have also soldierd the R7D2->R7D1 points as the other option. but still i am stuck thinking what may have gone wrong

thanks again

lordvader129 · « **Reply #1 on:** January 08, 2005, 11:27:00 AM »

evox cant flash winbonds, it hangs on erasing

try raincoat .7 (it also resizes a 256k bios to fit a 1mb chip, but your chip is 256k)

if raincaot gives flash not writable clean off your sodler points and resolder them

zipo1200 · « **Reply #2 on:** January 09, 2005, 12:17:00 PM »

Thx i have gotten .7 from the splintercell raincoat exploit and was able to successfully telnet. but one problem. when i get into the raincoat directory (following directions in readme) and when i get this:

#
./raincoat -r

i get the following file or directory does not excist.

what may bbe going wrong since i was able to cd../. to the directory

lordvader129 · « **Reply #3 on:** January 09, 2005, 12:52:00 PM »

you need to specify what raincoat will read to, liek this

./raincoat -r orig_bios.bin

zipo1200 · « **Reply #4 on:** January 09, 2005, 05:58:00 PM »

if i do recall

./raincoat-r orig_bios.bin

reads the bios and then writes a backup. unfortunatly i get the same error

any other suggestions

terrorvis · « **Reply #5 on:** January 10, 2005, 01:37:00 AM »

If you can't 'read' the bios either, then it really does sound like your soldering needs re-doing.

Exobex · « **Reply #6 on:** January 10, 2005, 04:36:00 AM »

Just put in

./raincoat

If it doesn't work, you're not in the right directory, normally /media/E/UDATA/4541000d/000000000000/raincoat

This post has been edited by Exobex: Jan 10 2005, 12:37 PM

Gunzz11 · « **Reply #7 on:** January 10, 2005, 09:01:00 AM »

did you solder both set of points on top and bottom i though i had done this to when i flashed a 1.4 but i double checked and there were points on the bottom that needed to be soldered.

zipo1200 · « **Reply #8 on:** January 10, 2005, 02:42:00 PM »

Alright. well i'll be heading back over there to finish this box off. i'll resodier the points to make sure. and yes 3 points are soldierd just to make sure.

now when u go "MEDIA/e/uDATA...ETC

now media being as linux looks for a drive to mount?

Exobex · « **Reply #9 on:** January 10, 2005, 05:31:00 PM »

?

Log in as root, password xbox
cd /media/E/UDATA/4541000d/000000000000/raincoat
./raincoat

Author Topic: Winbond (Read 84 times)