xboxscene.org forums

Author Topic: Flashing St M29f002bt70n1  (Read 77 times)

a300

  • Archived User
  • Newbie
  • *
  • Posts: 4
Flashing St M29f002bt70n1
« on: February 27, 2004, 12:11:00 PM »
Hi

I`ve a 1.4 box (10-10-2003) with ST M29F002BT70N1 chip, and this s**t don`t flash.
I doublechecked the solder points. Repaint them about 10 times with defrogger reapair kit paste. (Also that one is on the back of the mainboard)
I tried raincoat 0.7 and 0.501 also, with no success.

Any idea?
Logged

lordvader129

  • Archived User
  • Hero Member
  • *
  • Posts: 5860
Flashing St M29f002bt70n1
« Reply #1 on: February 27, 2004, 12:52:00 PM »
what does it say when you try to flash?
Logged

a300

  • Archived User
  • Newbie
  • *
  • Posts: 4
Flashing St M29f002bt70n1
« Reply #2 on: February 27, 2004, 02:53:00 PM »
It says:

"INVALID MANUFACTURER ID: 0x09
Check that your flash-enable points are correctly soldered, that the
neighbouring circuitry is not damaged, and that any A18 or A19 switches
are correctly set.
Valid manufacturer IDs can be found at:-
http://www.jedec.org/DOWNLOAD/search/JEP106n.pdf"


But the pins are 100% closed...
Logged

a300

  • Archived User
  • Newbie
  • *
  • Posts: 4
Flashing St M29f002bt70n1
« Reply #3 on: February 27, 2004, 03:07:00 PM »
I downloaded raincoat 0.7 from: http://www.geocities.com/mspritch/raincoat.html
When I try to read the original bios it says: 151 types read....  and after that: INVALID MANUFACTURER ID: 0x09

I am 100% sure the pins are correctly connected. I did it about 40-50 times before...
Logged

lordvader129

  • Archived User
  • Hero Member
  • *
  • Posts: 5860
Flashing St M29f002bt70n1
« Reply #4 on: February 27, 2004, 03:22:00 PM »
they arent bridged, make sure there arent any broken traces anywhere, check with a multimeter
Logged

a300

  • Archived User
  • Newbie
  • *
  • Posts: 4
Flashing St M29f002bt70n1
« Reply #5 on: February 27, 2004, 03:39:00 PM »
Ok I`ll check them tomorrow. And what about that point at back of the board. So it must connected, or not? Is that 2 on top is enough?
Logged

lordvader129

  • Archived User
  • Hero Member
  • *
  • Posts: 5860
Flashing St M29f002bt70n1
« Reply #6 on: February 27, 2004, 04:35:00 PM »
2 on top should be fin, but if your having trouble it never hurts to have a little redundancy
Logged

Exobex

  • Archived User
  • Hero Member
  • *
  • Posts: 1093
Flashing St M29f002bt70n1
« Reply #7 on: March 01, 2004, 08:52:00 AM »
They COULD be bridged, but if the resistors near the jumpers are bridged or removed, you'll get the same problem.
Logged

xxxbigchuck

  • Archived User
  • Newbie
  • *
  • Posts: 6
Flashing St M29f002bt70n1
« Reply #8 on: March 03, 2004, 07:32:00 AM »
Did you ever get this to work??? I've got the same problem. Also I noticed in the raincoat.conf file that St M29f002bt70n1 isn't listed in the copy of the .7 that I have. Was it in yours??? If you've fixed this please let me know what you did. :D  
Logged

Exobex

  • Archived User
  • Hero Member
  • *
  • Posts: 1093
Flashing St M29f002bt70n1
« Reply #9 on: March 03, 2004, 08:01:00 AM »
QUOTE (xxxbigchuck @ Mar 3 2004, 04:25 PM)
Did you ever get this to work??? I've got the same problem. Also I noticed in the raincoat.conf file that St M29f002bt70n1 isn't listed in the copy of the .7 that I have. Was it in yours??? If you've fixed this please let me know what you did. :D

This entry...
QUOTE (raincoat.conf)
Flash = 0x20b0,"ST M29F002T/NT/BT/BNT",0x40000

does the trick.

See here (scroll to page 17) to find out why.
Logged