Topic: 0x00, 0x09 Error When Flashing (Read 92 times)

lukano · « **on:** January 20, 2004, 07:11:00 AM »

I've posted Here! and I'm wanting to find out if the issue I'm having is caused due to the version of raincoat I'm using (I thought I had grabbed the newest) or if it was something altogether different.

Any clue?

choad420 · « **Reply #1 on:** January 29, 2004, 04:28:00 AM »

this one def needs pinned u got my box going tyvm.

ps2wiz · « **Reply #2 on:** March 10, 2004, 03:49:00 PM »

Question, whats wrong with this definition?

lordvader129 · « **Reply #3 on:** March 10, 2004, 04:01:00 PM »

0x0900 is NOT a real chip, it means the chip is not write enabled

go find any non-winbond TSOP, desolder the write enable points and ID it with evox, it will show up as an 0x0900 winbond, then solder the points and check again, it will show up correctly

Exobex · « **Reply #4 on:** August 12, 2005, 11:46:00 AM »

It's 29-wire modchip time.

Exobex · « **Reply #5 on:** August 11, 2003, 09:09:00 AM »

If you get the 0x09, 0x00 error, check your soldering on the point near the LPC port.

If you get "flash not writable", check your soldering on the point near the TSOP (topside or bottomside, whichever one you used).

If you can't get the solder to bridge the jumpers properly (it balls up on either side instead), you can instead tin the points and solder a single strand of wire across them, then snap off the excess (carefully) leaving you with a 3mm wire bridge.

On virtually every post where people have had the 0x09, 0x00 problem, resoldering the jumpers has cured the problem.

On a few others, the problem is that the resistor marked R7D2 has been accidentally removed. IF THIS IS NOT THERE, YOU CANNOT FLASH THE TSOP! If you've lost it, replace it with another 10K resistor. Don't just replace it with a gob of solder and whinge when it doesn't work, that's just being thick.

Also don't forget, if you're working on a 1.2/1.3 machine, raincoat 0.3 won't work, you've got to update it to 0.5 (or better still 0.501).

The following is NOT the solution:-

smokeingit · « **Reply #6 on:** August 11, 2003, 03:12:00 PM »

its already been pinned http://forums.xbox-s...3&t=58058&st=50
AND
i already made a thread on this http://forums.xbox-s...tupid,and,guide

Exobex · « **Reply #7 on:** August 13, 2003, 09:57:00 AM »

Yes, but no bugger seems to be reading 'em! Unless the answer's staring them in the face (in the topic title, for example), they just post it as another topic. Again.

Exobex · « **Reply #8 on:** August 18, 2003, 09:13:00 AM »

Exobex · « **Reply #9 on:** August 27, 2003, 08:01:00 AM »

They're creeping in again, so this post is just to bring this topic to the top.
(can someone pin it please?)

Xeero · « **Reply #10 on:** August 27, 2003, 08:04:00 AM »

QUOTE (Exobex @ Aug 13 2003, 01:57 PM)

Yes, but no bugger seems to be reading 'em! Unless the answer's staring them in the face (in the topic title, for example), they just post it as another topic. Again.

Why, what did you do?

Exobex · « **Reply #11 on:** September 05, 2003, 01:44:00 PM »

dmp · « **Reply #12 on:** December 02, 2003, 03:36:00 AM »

well, first start you only need the top two points.

I wish we could get rid of that inaccurate tutorial that mentioned all three as it is completely false and based on folklore...

other than that, I have no idea. soldering the bottom point is well would not normally cause this error but it is unnecessary.

David

Exobex · « **Reply #13 on:** December 11, 2003, 08:59:00 AM »

QUOTE (evolver56k @ Dec 1 2003, 10:38 PM)

i have a v1.4 xbox with the winbond w49f020t. i have soldered all 3 points on the board, and checked the soldering with a multimeter (all points are 100% correct). though i am still getting the 0x09 error with raincoat .501 (i downloaded raincoat from exobex's links). i can read my original bios to file but when i want to flash, raincoat also says its still write protected. i have been reading through all the posts and i cannot find any answers. are there any other traces i can solder? any help will be greatly appreciated.

[email protected]

Only the top points need to be soldered on 1.2/1.3/1.4/1.5 Xboxes. Check that you're soldering the correct pairs of jumper points, and that you're doing it correctly (people have been known to misinterpret the notes and link the two sets of points together with a piece of wire).
If the top jumper nearest the TSOP is correctly soldered, a multimeter connected across the jumper on the bottom of the board will show that there is continuity (of a few ohms tops - much more and your soldering ought to be re-done).

Author Topic: 0x00, 0x09 Error When Flashing (Read 92 times)