Topic: Tsop Flashing On v1.2-1.5 (Read 867 times)

sarcoptic · « **on:** December 31, 2003, 03:05:00 AM »

Tsharkou, sounds like the August model could of been a 1.3 while the Septemeber one was a 1.4. All in all the 1.4 one is dead. The 1.4 contains the focus video encoder which needs either the Evox M7 or X2 4979.06 to work. The 1.3 has a conexant video encoder and this is why the older X2 4977 worked fine. Definitely check the guide for confirmation of this. Version Guide

Exobex · « **Reply #1 on:** December 31, 2003, 03:39:00 AM »

The safest bet is to use ONLY THE LATEST BIOS! In other words, keep M7 and/or 4979, delete the rest, otherwise sooner or later you're going to flash a 1.4/1.5 machine with D6 or an early X2 BIOS, and you're screwed.

DevoDave · « **Reply #2 on:** January 03, 2004, 09:53:00 PM »

QUOTE (deude @ Dec 17 2003, 08:29 PM)

Hey guys I need some help!! I'm trying to flash a 1.3
when I type ./raincoat -p 256bios.bin it shows:

DETECTED: Hynix - HY29F002 (256K)
Programming with 256bios.bin...unable to open file

The file I'm using is 007AUF_RAIN0501_M7_256
any suggestions!!!

You need to specify the name of the BIOS file as a parameter when you run the file with ./raincoat -p

make sure that the BIOS file exists. Try ls to get a directory listing.

If your BIOS file is called BIOSNAME.BIN then use ./raincoat -p BIOSNAME.BIN to flash it.

thadude · « **Reply #3 on:** January 04, 2004, 11:58:00 AM »

When I use raincoat it doenst find raincoat.conf....its looking for it in /etc
but its not there, its in the same directory....

Could I possible get raincoat off one of you guys to see if its the copy that I am getting???

thanks in advance

joejack · « **Reply #4 on:** January 04, 2004, 07:12:00 PM »

Was referring to the points identified in the photo found in the flashing tutorial (don't know the reference). It's on this site I believe.

dfn_doe · « **Reply #5 on:** January 06, 2004, 01:35:00 AM »

w00t I just succesfully flashed a 1.5 with a winbond w49f020t using raincoat .51 and only the two point on the top of the board. I cut 2 very smaller pieces of the lead off a resistor I had sitting around and used them as tiny jumpers between the pads since I have read sooo many reports of people soldering this connection multiple times to get a goot joint. Worked first try! Thanks to everybody on this forum who helped develop these hacks!

whosyerdaddy · « **Reply #6 on:** January 07, 2004, 11:08:00 AM »

Has anyone tryed this with a 1.4 or 1.5 I have a 1.5 and I am trying not to buy a chip since I have been doing the 1.2 and 1.3. I am stuck on a 1.5 board the bottom of the board is diffrent and it does not have one of the sodering points? Please help.
R7D10 I find but the one below I can't? I just need to know what points to soder on a 1.5 board.

BaDvs3viL · « **Reply #7 on:** January 07, 2004, 12:05:00 PM »

Ver's 1.2 all the way upto 1.5 has the same top 2 solder points....I have done so many of these......

dfn_doe · « **Reply #8 on:** January 10, 2004, 02:52:00 AM »

QUOTE (whosyerdaddy @ Jan 7 2004, 09:08 PM)

Has anyone tryed this with a 1.4 or 1.5 I have a 1.5 and I am trying not to buy a chip since I have been doing the 1.2 and 1.3. I am stuck on a 1.5 board the bottom of the board is diffrent and it does not have one of the sodering points? Please help.
R7D10 I find but the one below I can't? I just need to know what points to soder on a 1.5 board.

guess what... if you read the posts instead of just asking questions you would have your answer... the post I made directly above yours has the answer to your question.

chasmosis1 · « **Reply #9 on:** January 12, 2004, 04:19:00 PM »

Version 1.3 with Winbond, soldered top two points only, tried to flash with 007 with evox installer - hung at erasing flash 0% twice, flashed sucessfully first time with 007 with raincoat after adding 0.501 raincoat (did not try with older version).

iLLNESS · « **Reply #10 on:** January 13, 2004, 09:15:00 AM »

top 2 points with winbond W49020T-90B

used raincoat 0.501 evox doesnt work

sdpnoy · « **Reply #11 on:** January 15, 2004, 10:57:00 AM »

Manf. Date 5/2003
Winbond
Top 2 solder points with 007 exploit. Worked like a charm

Gianmarco · « **Reply #12 on:** January 16, 2004, 02:01:00 AM »

Hi everyone,

FYI I successfully TSOP flashed a v1.3 Xbox with Winbond W49F020T-90B chip on it using raincoat 0.501 + X2 4979 bios without needing to bridge the bottom points and also without using this line in raincoat.conf :

Flash = 0x0900,"Winbond W49F020T",0x40000

Chip has been recognized as Winbond - W49F020.

Thx to the Xbox community.

52volts · « **Reply #13 on:** January 17, 2004, 09:42:00 PM »

Flashed a 1.2 or 1.3 version using raincoat007 (had to replace two files whit the .501, raincoat and raincoat.conf for it to flash) and only solder the tow top points. Had a Hynix - HY29F002 flashed with M7. MFD of xbox 6/29/03.

dachef26 · « **Reply #14 on:** January 20, 2004, 08:31:00 PM »

Is raincoat .501 the current one on #xbins? I'm having trouble flashing my 1.4, and am curious if that is the problem.

Author Topic: Tsop Flashing On v1.2-1.5 (Read 867 times)