Topic: Tsop Flashing On v1.2-1.5 (Read 873 times)

Loud · « **Reply #60 on:** September 06, 2003, 11:12:00 PM »

I just flashed a 1.3 today with the Hynix chip. I only bridged the top two points. Flash went fine with MA and evox. I did have to add the line

Flash = 0xadb0,"Hynix - HY29F002",0x40000

in evox.ini to get it to flash.

DaShiZNiT · « **Reply #61 on:** September 10, 2003, 05:21:00 AM »

scored me a Samsung too, but all I did was solder the two topside points, and updated my evox.ini with

Flash = 0x20b0,"ST - 29F002",0x40000

at first it said flash unwriteable, then I knew that I had to update the *.ini

so whats the bottom point all about? I checked it with a meter and it seems to be the same as one of the top points..

Veckans · « **Reply #62 on:** September 12, 2003, 02:48:00 AM »

I've flashed two v1.3 boxes:

One with Winbond and one with Hynix. I connected only the top points (using conductive ink), and flashed using raincoat.

This post has been edited by Veckans: Sep 12 2003, 09:52 AM

cONEction · « **Reply #63 on:** September 14, 2003, 08:22:00 AM »

conclusion : RAINCOAT 0wns!

Th3_H0unD · « **Reply #64 on:** September 15, 2003, 04:25:00 AM »

I have a V1.3 TSOP: Hynix HY29F002TTH-90

I seen someone have a Hynix HY29F002TT-90 is it the same ?
If so what is the evntry in the evox.ini is it Flash = 0xadb0,"Hynix - HY29F002",0x40000 ?

I haven't seen any other entries posted.

cONEction · « **Reply #65 on:** September 15, 2003, 09:52:00 AM »

joecool · « **Reply #66 on:** September 16, 2003, 02:57:00 PM »

Is it safe to assume there is no raincoat exploit for Mechassult like there is for 007?

Or even an app that I can select from evox (edit the ini) and use that to flash?

Update, I have one of the winbond chips without having a 007 original. So I simply copied the raincoat section of the 007 hack to the Mechassult hack and ran raincoat to flash my tsop (needs a full chip erase). works great!!!

as said previously... raincoat/linux rules!!!!!

SLAM-ER · « **Reply #67 on:** September 18, 2003, 12:36:00 AM »

HELP!!!

/EDIT #2
OK it's official, I am an idiot. Yes 0x09, 0x00 indicates bad solder, as already discussed. There are TWO solder points on the top (the last one I did only had 1). Do both of them and it works. (duh!)

Thanks! :/

nicoworld · « **Reply #68 on:** September 19, 2003, 05:58:00 PM »

and me for a 1.3 i'm stopped here!!!

# cd /media/E/UDATA/4541000d/000000000000/raincoat/
# ls
BootFlash.c README raincoat.c
BootFlash.h _#Makefile.1.1.1.189B8 raincoat.conf
CVS bios.bin raincoat.katefl
EvoX D.6 256k.bin boot.h
Makefile raincoat
# ./raincoat -p bios.bin
raincoat Flasher 0.501 Apr 14 2003 [email protected] http://xbox-linux.sf.net
Reading in ./raincoat.conf... 18 flash types read

DETECTED: Winbond W49F020T (256K)
Programming with bios.bin...Read 262144 bytes from file
Erasing...
Trying to erase whole chip
ERASE ERROR AT +0x0...read 0x09
Done
Error: Erase failed for block at +0x0, reads as 0x09
Could your chip be write-protected?
Completed

the two point are both (excuse me for my english)

and i'm test raincoat 5.01..

and write protect....

ViPeR-7 · « **Reply #69 on:** September 19, 2003, 06:50:00 PM »

1.3 winbond using the 2 points on top using the 007 exploit

Dansken · « **Reply #70 on:** September 21, 2003, 04:37:00 AM »

xbox v1.3 TSOP: Hynix HY29F002TT-90
solder top points
29wire homebrew
flashed TSOP whit EvoX.

Klaus · « **Reply #71 on:** September 21, 2003, 10:03:00 AM »

v1.3
Top two joints
EvoX
Added line Flash = 0x20b0,"ST - 29F002",0x40000

Props to DaShiZNiT, your post got me there

desertboy · « **Reply #72 on:** September 22, 2003, 03:44:00 PM »

3 1.3's the 2 top points
14 1.1 the 2 points in the pinned guide.

I know how many Xbox's because I keep their proms (And give them away)

All 007 raincoat flashes

cypher35 · « **Reply #73 on:** September 23, 2003, 01:26:00 PM »

Ed_209 · « **Reply #74 on:** September 23, 2003, 02:09:00 PM »

Author Topic: Tsop Flashing On v1.2-1.5 (Read 873 times)