xboxscene.org forums

Pages: 1 2 [3] 4 5

Author Topic: Successful Install On 1.6 Console!  (Read 446 times)

MicroChip

  • Archived User
  • Newbie
  • *
  • Posts: 19
Successful Install On 1.6 Console!
« Reply #30 on: July 13, 2004, 05:31:00 PM »
Ok my ice came today (ordered yesterday, props to Modwhiz).  I put the pinheader in, rebuilt the lpc to it, soldered the included 2 wire piece to lframe and ground, then it frag'd.  I took it apart, checked all the solder points, put it back together, booted fine, except, I use HDTV adapter, NTSC, and the Xenium OS is in black and white.

Wierd thing is I popped my usb pendrive in, loaded M8-1.6, set autoboot to that, and when I press the On button, it goes to that bios in color.  When I press eject to turn on, I get Xenium OS2 in black and white.

any ideas?

MC
Logged

bmoney03

  • Archived User
  • Jr. Member
  • *
  • Posts: 64
Successful Install On 1.6 Console!
« Reply #31 on: July 13, 2004, 06:59:00 PM »
Well back to my orig ques: Do i need to install the pin headers? If not then what wire to i install on the chip? Thanks
Logged

Ace25

  • Archived User
  • Sr. Member
  • *
  • Posts: 476
Successful Install On 1.6 Console!
« Reply #32 on: July 13, 2004, 07:30:00 PM »
QUOTE (bmoney03 @ Jul 13 2004, 06:59 PM)
Well back to my orig ques: Do i need to install the pin headers? If not then what wire to i install on the chip? Thanks

yes, install the pin header and make sure to remove the one pin out of it. It pulls out easily with a pair of pliers.
Logged

counter terrorist dan

  • Archived User
  • Full Member
  • *
  • Posts: 178
Successful Install On 1.6 Console!
« Reply #33 on: July 13, 2004, 08:23:00 PM »
so.. after all this confusion, one question:

Are there any clear, 100% been tested, positive working and informative manuals or tutorials (preferably really forgiving with knowledge barriers and explaining what some of the shit is?) on installing Xenium Ice on a v1.6?
Logged

Master-Chief

  • Archived User
  • Hero Member
  • *
  • Posts: 1352
Successful Install On 1.6 Console!
« Reply #34 on: July 14, 2004, 05:00:00 AM »
QUOTE (counter terrorist dan @ Jul 14 2004, 01:23 AM)
so.. after all this confusion, one question:

Are there any clear, 100% been tested, positive working and informative manuals or tutorials (preferably really forgiving with knowledge barriers and explaining what some of the shit is?) on installing Xenium Ice on a v1.6?

Follow the OZXodus Tutorial on installing a Xenium on a 1.6. Follow it JUST like it says. Don't worry about what we are saying here because some of it is about the blue Xenium chip and you don't have that. It seems that the ICE version and the regular blue Xenium have a significant difference other than just the color.  ohmy.gif
Logged

Master-Chief

  • Archived User
  • Hero Member
  • *
  • Posts: 1352
Successful Install On 1.6 Console!
« Reply #35 on: July 14, 2004, 09:29:00 PM »
wink.gif
Logged

dzv

  • Archived User
  • Sr. Member
  • *
  • Posts: 432
Successful Install On 1.6 Console!
« Reply #36 on: July 15, 2004, 01:18:00 AM »
The OzXodus 1.6 manual offers a choice of 2 different methods of LPC rebuild.  One method involves working on the top of the motherboard, while the other involves working on the bottom of the moterboard.  You DO NOT need to do both.

If you're gonna go through the hassle of the LPC rebuild, then there's really no good reason to use the solderless adaptor.
Logged

netrave

  • Archived User
  • Newbie
  • *
  • Posts: 6
Successful Install On 1.6 Console!
« Reply #37 on: July 15, 2004, 09:28:00 AM »
is the SMARTXX chip the EXACT SAME diagram for installing an ICE??

now i know i have to solder the D0 to the chip on my ICE and 1.6...

what im not understanding, is there 2 spots that i can get the D0? one from the TOP and one from the BOTTOM??

cause it seems that the BOTTOM of the board is MUCH easy to see and not mess up then the top?

can i just get the D0 from the bottom and run it thru a hole and solder to the chip?
Logged

netrave

  • Archived User
  • Newbie
  • *
  • Posts: 6
Successful Install On 1.6 Console!
« Reply #38 on: July 15, 2004, 09:41:00 AM »
i mean the LFRAME on the bottom of the board using the SMARTXX diagram to the D0 on the chip?

cause the Xenium diagram shows to get the D0 from the top of the motherboard to the chip... but i dont wanna do it that way...
Logged

MicroChip

  • Archived User
  • Newbie
  • *
  • Posts: 19
Successful Install On 1.6 Console!
« Reply #39 on: July 15, 2004, 09:53:00 AM »
QUOTE (netrave @ Jul 15 2004, 06:41 PM)
i mean the LFRAME on the bottom of the board using the SMARTXX diagram to the D0 on the chip?

cause the Xenium diagram shows to get the D0 from the top of the motherboard to the chip... but i dont wanna do it that way...

I don't know if that will work.  Do the LPC rebuild on the bottom of the board like in the Xenium ICE 1.6 install manual, and use the LFRAME on the top as in that same manual.  The LFRAME on top was easy, much easier than the LPC rebuild.  The included wire (blue and black with a plug) makes it easy.  Stick the blue wire in the d0, warm it up with your soldering iron, it's already tinned and will just stick.  Then solder the black one to the screw-hole next to the ICE, and plug the end in to the ICE.

FYI, the LPC rebuild would be easy too if I had some Kynar 30awg precut and tinned, I think modchip sellers should include that or charge like $5 for it.  I used IDE wire and it was a bit trickier...

MC
Logged

Ace25

  • Archived User
  • Sr. Member
  • *
  • Posts: 476
Successful Install On 1.6 Console!
« Reply #40 on: July 15, 2004, 11:38:00 AM »
On that last question about the 3.3v they both work. You can do either method.

There still seem to be questions about the install.. so.. let me lay out the Normal Xenium questions that I have (and will answer later on tonight).

Normal Xenium:
1. Do you need to install the top side D0 like the Ice version? (I believe "No")

2. If you use the plug-in D0/Ground wire that comes with the chip do you still need to ground the LFrame since your grounding the D0 point to ground on top? And will that give you TSOP capability?

Those are questions I can and will answer myself tonight when I get home.

Xenium Ice:
Ummm, really can't think of any Ice questions, I think they have been covered. The only thing "extra" that needs to be done on the Ice chips is to solder the LFrame point to the D0 point on the chip instead of grounding it (running the wire through an open LPC hole). Other than that, just follow the Xodus instructions completely.
Logged

netrave

  • Archived User
  • Newbie
  • *
  • Posts: 6
Successful Install On 1.6 Console!
« Reply #41 on: July 15, 2004, 12:31:00 PM »
ok i just got the XENIUM ICE IN!!! im anxious...

now i see that there is 2 pieces where i dont knwo what to do with them...

there is a USB port, where do i wire that into???

is there a diagram for this as well???

and there is a blue and black wire that plug into the chip... where do these go!?? and last question..


there looks like an adapter for hdtv or something... can i leave this piece off, or do i have to plug it in? and if so, does it matter which way i put it in?
Logged

netrave

  • Archived User
  • Newbie
  • *
  • Posts: 6
Successful Install On 1.6 Console!
« Reply #42 on: July 15, 2004, 12:40:00 PM »
and im a real dubm a$$ when it comes to this stuff, this is my first one... hwo do u know which way to plug the chip into the header pins?
Logged

Ace25

  • Archived User
  • Sr. Member
  • *
  • Posts: 476
Successful Install On 1.6 Console!
« Reply #43 on: July 15, 2004, 12:53:00 PM »
Chip installs towards to left side of the Xbox case on the Pin headers. Yes it can be installs wrong/backwards. So make sure the pin header on the modchip is on the right side of the chip when flipped upside down.
Logged

appleguru

  • Archived User
  • Hero Member
  • *
  • Posts: 1200
Successful Install On 1.6 Console!
« Reply #44 on: July 15, 2004, 01:12:00 PM »
biggrin.gif('Course, I had some nice Kynar wire I got at radio shack for $3 (50ft, wirewrapping wire or w/e).

As for the differences in Blue/ICE Xeniums, I'm one to believe it's all software (XOS2 beta vs XOS2 pre-release). AFAICT the Hardware is exactly the same (Of course, until Xenium releases XOS2 for download or someone manages to make/distribute a .bin for the OS from an ICE, we'llnever know...)
Logged
Pages: 1 2 [3] 4 5
« previous next »