Topic: Yet Another Xenium Problem (Read 111 times)

JesseWHHS · « **on:** January 24, 2004, 03:23:00 PM »

maybe the hooksup on the TV are loose inside since it worked then it didnt. But maybe the TV its self was the problme. What brand TV did you have it fail on?

resolost · « **Reply #1 on:** January 24, 2004, 04:03:00 PM »

it sounds to me that theres somthing loose in the soldering if it goes in and out...IMO

jeffaknight · « **Reply #2 on:** January 27, 2004, 10:28:00 AM »

I found out why it didn't work on my main TV. I was using an advanced AV kit with a Dolby Digital connection. My other TV was just RCA jacks. So not only does it not work with the HDTV kit, it does not work with Dolbly Digital Kit either. Not a big deal since once it is set up, it doesn't matter if you can see the Xenium startup screen.

billiebob · « **Reply #3 on:** January 27, 2004, 11:59:00 AM »

Can anyone else confirm this with the Adv A/V pack and HDTV...

Tidusblitz111 · « **Reply #4 on:** January 27, 2004, 04:02:00 PM »

HSDEMONZ · « **Reply #5 on:** January 27, 2004, 04:22:00 PM »

Tommy Vercetti · « **Reply #6 on:** January 28, 2004, 12:45:00 AM »

QUOTE (Tidusblitz111 @ Jan 27 2004, 09:02 PM)

You must have the standard(factory) video cables and audio cables to see anything for the modchip, many ppl have had the same problem.

Glad to help!

Is this ALL chips or just the Xenium?

And will the be a BIOS to cater to people with these setups?

I have a RCA Xbox ready TV with VPORT. So its like the adavanced AV Pack, but the TV has a Xbox ready VPORT in it. Will I experience the same thing?

jeffaknight · « **Reply #7 on:** January 28, 2004, 04:28:00 PM »

Mine is a 1.4 and does not work with the advanced pack using composite cable and dolby digital.

muddy · « **Reply #8 on:** January 28, 2004, 05:43:00 PM »

QUOTE (HSDEMONZ @ Jan 28 2004, 02:22 AM)

Correct.

Stand AV cables.. no fancy s-video cables.. no VGA box.. nadda.

My V 1.2 works great with S-Video...

evoxreloaded · « **Reply #9 on:** January 29, 2004, 08:19:00 AM »

1.3 here just tested and worx fine....its gotta be that focus encoder

Heifetz · « **Reply #10 on:** February 06, 2004, 08:43:00 AM »

I have exactly the same problem! When I have only D0 soldered, the xbox boots up, flashes red a few times, then the xenium screen comes up and then it flashes blue for a sec before rebooting. Does this mean that the chip is installed correctly??? I'm using a standard controller with standard rca cables.

It has been driving me nuts trying to solder different points over and over again. My xbox has the focus encoder, but I'm not sure if its 1.4 or 1.5. Does a 1.4 xbox need to have 3.3v and ground too? When I solder to those two points, my xbox frags instead of booting up to the xenium screen.

Hiker_42 · « **Reply #11 on:** February 07, 2004, 06:59:00 PM »

Yes. XeniumOS is Cromwell based and as we all know, there are Focus issues. It's supposedly all fixed in the upcoming release (you guys should drop by #ozxodus on EFnet, official Xenium support channel. They must LOVE answering all our questions... over and over and over and over.... hehe)

Just to recap; It's a FOCUS issue.

Author Topic: Yet Another Xenium Problem (Read 111 times)