Topic: Solderless 1.6/1.6b Install Tutorial - Xodus S.p. (Read 133 times)

RCC123 · « **on:** February 20, 2005, 12:14:00 PM »

Yeah... my host ACTUALLY works.

After lots of hard work, a stupid error, and a alot of learning, this tutorial has been compiled. If any of you have pre-ordered one of these nifty Universal Solderless adapters from www.modwhiz.com, then you'll really appreciate this. To my knowledge it's the only one out. I'm really stoked about a 4th-gen Universal Solderless adapter, it is compatible with all pinheader based mods, and of course all known Xbox-versions.

http://rcc123.no-ip.info/xodussp/

Enjoy the tutorial!!!

tutyet · « **Reply #1 on:** February 20, 2005, 01:31:00 PM »

very nice!

so did you do this your self and if so how did you get it so early!!!

again nice tut and i liked the little movies makes it look really easy!

RCC123 · « **Reply #2 on:** February 20, 2005, 03:57:00 PM »

Not yet.... I just compiled the research off of spiderchip.com (which they stole the idea from) and this site. I got the movie off of www.teamxodus.com.

RCC123 · « **Reply #3 on:** February 20, 2005, 05:06:00 PM »

Cool...so cool!

RCC123 · « **Reply #4 on:** February 20, 2005, 10:26:00 PM »

Up to top ^^^ !!!

RCC123 · « **Reply #5 on:** February 21, 2005, 12:26:00 PM »

Yes... and you will have to take the motherboard out of the case so as to solder the two points on the bottom, as shown in the tutorial for the X3.

RCC123 · « **Reply #6 on:** February 21, 2005, 04:41:00 PM »

of course as you know that is optional

RCC123 · « **Reply #7 on:** February 21, 2005, 08:36:00 PM »

Instead of covering the D0 you could also clip it off up by the connector for a cleaner install.

RCC123 · « **Reply #8 on:** February 22, 2005, 01:06:00 PM »

no prob, if anyone else has questions feel free to post

RCC123 · « **Reply #9 on:** February 23, 2005, 02:19:00 PM »

kremer... did it end up working out?

RCC123 · « **Reply #10 on:** February 25, 2005, 09:03:00 PM »

Can you send me a pic? The clear part is the guide.

Firemonkey44 · « **Reply #11 on:** February 25, 2005, 09:17:00 PM »

the adapter looks like this...http://www.modwhiz.com/store/product.php?productid=16154&cat=0&page=1 sorry i couldn't figure out how to paste a pic but this is the package that i bought. Thanks for the help by the way

RCC123 · « **Reply #12 on:** February 27, 2005, 08:15:00 PM »

That's not the Xodus S.P. That is the generic solderless adaptor. The Xodus S.P. can be found here:

http://www.modwhiz.c...&cat=248&page=1

If you have an Xbox v1.6 I recommend getting the Xodus S.P. it will save you the hassle of soldering and possibly killing your xbox.That is the adaptor that the tutorial is written for.

If you decide not to get the Xodus S.P. you will have to do an LPC rebuild (if xbox v1.6), and I wouldn't recommend using the solderless adaptor. Instead use the supplied pin header. You can find a tutorial here:

http://www.teamxodus...op=getit&lid=36

For versions 1.0-1.5 use this here:

http://www.teamxodus...op=getit&lid=33

Most of this info is from www.teamxodus.com check it out and take a look around.

Good Luck!!!

m82a1 · « **Reply #13 on:** February 27, 2005, 10:44:00 PM »

awsome tutorial, very well done, will be good for some n00bs

RCC123 · « **Reply #14 on:** February 28, 2005, 09:04:00 PM »

P.S. The tutorial link is

http://rcc123.no-ip.info/xodussp

...And you can use the silicone to hold the wires in once you have a good connection.

Author Topic: Solderless 1.6/1.6b Install Tutorial - Xodus S.p. (Read 133 times)