Topic: Alternate Way To Solder A Duox2 (Read 75 times)

bammer85 · « **on:** January 24, 2007, 08:52:00 PM »

Ok I messed up my LPC. There is a way to install every wire to the motherboard right? I saw it once, but I just don't remember where it is. Does anyone have an idea?

lakers#24 · « **Reply #1 on:** January 24, 2007, 08:58:00 PM »

ya i had to do it ire by wire because i messed up mine to if u have a v 1.o u have to flowlow this

http://www.duomodchip.com/english/install/...uox2gs_v1.0.jpg

This post has been edited by lakers#24: Jan 25 2007, 05:00 AM

bammer85 · « **Reply #2 on:** January 25, 2007, 10:54:00 AM »

QUOTE(lakers#24 @ Jan 25 2007, 04:58 AM)

ya i had to do it ire by wire because i messed up mine to if u have a v 1.o u have to flowlow this

http://www.duomodchip.com/english/install/...uox2gs_v1.0.jpg

I've seen that page before. I"m talking about directly to the board. my lpc is messed up and there is no solder there.

Allegro1 · « **Reply #3 on:** January 25, 2007, 04:29:00 PM »

Are you talking about a wire installation:

http://www.duomodchip.com/english/install/duox/wire.jpg

or the board installation:
http://www.duomodchip.com/english/install/duox/direct.jpg

If you messed up the LPC I would strongly encourage you to send your stuff to a Modder in the B/S/T section because these other installations need an even more delicate touch than the header.

Also note that the LPC ground pin is tied to a ground plane which is very stubborn to heat up. Too little heat and it won't flow, too much and the via pops out and the board scorches.

bammer85 · « **Reply #4 on:** January 25, 2007, 06:15:00 PM »

QUOTE(Allegro1 @ Jan 26 2007, 12:29 AM)

Are you talking about a wire installation:

http://www.duomodchip.com/english/install/duox/wire.jpg

or the board installation:
http://www.duomodchip.com/english/install/duox/direct.jpg

If you messed up the LPC I would strongly encourage you to send your stuff to a Modder in the B/S/T section because these other installations need an even more delicate touch than the header.

Also note that the LPC ground pin is tied to a ground plane which is very stubborn to heat up. Too little heat and it won't flow, too much and the via pops out and the board scorches.

No I'm not. My LPC isn't there anymore, and I was just wondering if there was a way to solder them somewhere else besides the lpc holes. I'm going to refil the LPC holes anyway and wire them all to the LPC holes.

Kadiblov · « **Reply #5 on:** January 29, 2007, 04:55:00 AM »

There is a way using these points here.

http://fixnchipz.co.uk/page18.html

But if you messed up your LPC, I strongly recommend you send this to a professional.

Good luck,
Kadiblov

bammer85 · « **Reply #6 on:** January 30, 2007, 04:00:00 PM »

QUOTE(Kadiblov @ Jan 29 2007, 12:55 PM)

There is a way using these points here.

http://fixnchipz.co.uk/page18.html

But if you messed up your LPC, I strongly recommend you send this to a professional.

Good luck,
Kadiblov

yeah my co-worker actually has it and is workig on it at the moment. Is that diagram for the v 1.6?

Alex548 · « **Reply #7 on:** January 30, 2007, 04:12:00 PM »

Did you read what's posted in the link?
There's a diagram for 1.0-1.4 and another one for 1.6 in there.
Make sure you're looking at the correct one.

The 1.0-1.4 diagram is for rebuilding a screwed up LPC.

bammer85 · « **Reply #8 on:** February 08, 2007, 12:32:00 PM »

well my box is ruined now. It doesn't boot to the old MS dash anymore (IMG:style_emoticons/default/sad.gif). I've got a new one on the way and I'm going to have a buddy solder it this time =). I don't know the version yet either.

Author Topic: Alternate Way To Solder A Duox2 (Read 75 times)