Topic: Duox2 Fragging On A V.1 Xbox. :( (Read 120 times)

ModdingManiac · « **on:** September 02, 2005, 11:30:00 AM »

Did he rebuild the LPC?

ModdingManiac · « **Reply #1 on:** September 02, 2005, 04:35:00 PM »

Sorry didn't see that.No he doesn't need to do the rebuild.....If the D0 is making contact with other open traces/connections then yes it could cause problems but if if you mean the is resting on the traces covered in lacker filling then no that couldn't be the problem

Chancer · « **Reply #2 on:** September 02, 2005, 04:40:00 PM »

D0 is working or the retail boot would be affected. BT is working as you can boot chip on or Chip Off.
FRAG with chip enabled is bad connections or damage/shorts on the LPC.
Post a pic of the work it may reveal all.

Spook8000 · « **Reply #3 on:** September 03, 2005, 06:31:00 PM »

Hi, I have the same problem as described here, and have a V1.0 XBox also.
Some questions I have are:

1. What is the normal mix of Bios's on the DouX2? Bank0 Xecuter v??/Bank1 Evox v???
2. Is it possible to see this problem and have a bad chip?
3. Is it possible that this problem is due to a DouX not being flashed with ANY bios?

I have seen this problem three times myself, and have nevr been able to resolve the actual problem. I have never been able to install a DuoX2 on an XBox at all, and the only common tread with me is that the XBox versions were always 1.2 or less.
But I can definately say that the LPC was soldered with a header, and the DouX did not work on them, but when another chip ie Xecuter was installed (with a few extra header pins) It worked fine!

So what is going on here?

Cheers, Spook8000

SubKelvin · « **Reply #4 on:** September 03, 2005, 10:51:00 PM »

Chancer · « **Reply #5 on:** September 04, 2005, 04:16:00 AM »

QUOTE

Maybe this will tell if it's the chip or soldering.

I can't get the links to work. I will just switch to iE and see if its my browser.

HackDaBox · « **Reply #6 on:** September 04, 2005, 07:57:00 AM »

try visiting this site first chancer then try to look at some of the pics

http://pics.bbzzdd.c...php?mode=latest

HackDaBox !

antz1970 · « **Reply #7 on:** September 04, 2005, 12:35:00 PM »

i aint looked @ all the pics yet but this pic http://pics.bbzzdd.c...ma/PICT0058.JPG it looks to me like r7d4 next to the lpc bus has been dislodged , could be wrong tho , i will look @ the rest of the pics and edit if i see anything else

**edit** the lpc looks a fuggin mess , not sure if its the pics or it could be flux making it look worse , i would clean that up and have a better look

SubKelvin · « **Reply #8 on:** September 04, 2005, 02:24:00 PM »

R7D4 was still connected at one point so I swung it around to where it is supposed to be with some small tweezers.

And it's not fragging, but now i'm getting error code 05(HDD not locked) which means the chips not working.

It boots going to MS Dash if I boot with power or eject.

Any ideas, i'm going to fool around with it now.

At least it's progress.

Chancer · « **Reply #9 on:** September 04, 2005, 02:32:00 PM »

QUOTE

Ok, I took my box to a professional to be soldered.(But not an xbox pro.)

Whats he a pro at? Obviously not soldering the LPC is a mess you should have done it yourself.

The install needs re-doing soldering wise. I would solder the D0 to the alt point , re-solder the LPC and cleanly if poss. Solder BT to the Alt point.
The LPC should look more like this
user posted image

SubKelvin · « **Reply #10 on:** September 05, 2005, 09:37:00 PM »

Is it most likely the soldering?

Chancer · « **Reply #11 on:** September 06, 2005, 02:40:00 PM »

Its definetely the soldering.
Put bluntly I could have thrown the solder at the LPC blindfold from 50 yards away and the LPC would look better.
If you can solder re-do it. If you can't take it to someone who really can solder (not the person who did it)

Author Topic: Duox2 Fragging On A V.1 Xbox. :( (Read 120 times)