Topic: Doux 2 Problems (Read 180 times)

HackDaBox · « **Reply #15 on:** May 07, 2005, 07:01:00 AM »

T0kEnHeRb ,

How are you going now ? did you get it flashed ?

I have just updated my flashing guides for all chips so check them out and report back here ok.

HackDaBox !

x_quest · « **Reply #16 on:** August 02, 2005, 09:19:00 PM »

Question for Chancer or HackDaBox or anybody who could help me.

Right now I have (4) Duo X2 Cromwell/flashbios Clones - they came preflashed with hacked bioses. After some experimenting I managed to screw three of those mods up. with my last remaining mod I managed to flash one the chips using the hotswap method and the slayers.26 disc. Now I connected the BT point to pin 9 and soldered D0 to ground near the LPC as described in previous tuts. by Chancer and HackDaBox. Now like I said I managed to save one but the other two are giving me problems.

I tried to flash one of them (which was working fine) with the X2 5035 bios and cant get it to do anything now no blinking red Led. I tried using the Hotswap method but I got the Not Flash writable message or something. Afterwards I did read the HackDaBox post about not flashing the clone Duo X2 with any X2 50xx bios. Too late for that. Could this chip still be salvaged? Or should I throw it away?

Now the other chip, I managed to successfully flash it using the hotswap method but when I tried to boot I got the 3on/3off flashing green/red frag. I tried both banks to no avail. The red led turns on when I hotswap it. What could be the problem?

x_quest

x_quest · « **Reply #17 on:** August 03, 2005, 11:35:00 AM »

HackDaBox · « **Reply #18 on:** August 03, 2005, 04:00:00 PM »

So try hotswaping after booting the good chip and use evox my HackDaBox Reflash Cd to do the flashing.

HackDaBox !

x_quest · « **Reply #19 on:** August 03, 2005, 10:17:00 PM »

Thanks for responding, I tried your reflash DVD and it didn't work.

Here's my problem again,

one chip says "Flash not writable". I dont get the red flashing LED anymore. This all started when I tried to flash the chip with the latest X2 Bios -5035.

The other chip during hotswapping flashes the RED LED. I flash and get the three on/off red/green FRAG anyways.

HackDaBox · « **Reply #20 on:** August 04, 2005, 08:13:00 AM »

OK.

Do you have a wire soldered from d0 on motherboard to ground ( like the metal circle around a screw hole ) and another wire soldered on the chip from BT to pin 9 ( pictured as G in the duomodchip.com diagrams )

if not then you need to fit these link wires and make sure you fir the BT to G wire on both duox2's The good one that you boot on and the bad one also.

Then try flashing again. If you have allready got these link wires in place theni am afraid you may have damaged the chips.

Maybe you would want to send them on to me or chancer for testing purpose. I can't really understand how a new bios could kill a chip but i have seen a few weird things from this bios posted now.

HackDaBox !

x_quest · « **Reply #21 on:** August 04, 2005, 09:16:00 AM »

Yeah I already have the D0 grounded to the screw round metal piece on the motherboard and connected BT to pin 9 on the good and bad chips. I'll send to you guys if you want to check them.
PM me a mailing address.

x_quest · « **Reply #22 on:** August 04, 2005, 09:18:00 AM »

Yeah I already have the D0 grounded to the screw round metal piece on the motherboard and connected BT to pin 9 on the good and bad chips. I'll send to you guys if you want to check them.
PM me a mailing address.

unlockman · « **Reply #23 on:** August 04, 2005, 10:58:00 AM »

Start a new topic this is not the same as the above problems
Chancer

Author Topic: Doux 2 Problems (Read 180 times)